Atom Chip Computer Efi/uefi, Need Distro Suggestions.

Hello All, I am a newbie to Linux I have used computers for years & would say I'm certainly not computer illiterate, however I am completely new to Linux. Hubby & I have a netbook each & I wanted to give linux a go on them. I installed Mint 17.1 Xfce on mine & am loving it, not really having any problems. However this is not the case with hubby's netbook....which has the following spec:

eeepc 904HD
80 GB HDD
Intel Celeron M, 897 mHz (512 cache, 32 bit)
995 mb RAM
VGA - intel 915/GMS/910GML express graphic controller (rev04)

(mine has the atom processor & was shipped with windows 7 starter which I have dual booted with mint

On hubbys we have tried the following distros:
Mint 17.1
Mint 13
Lubuntu
Xubuntu
Zorin 9 lite
Bhodi 3.0.0

The problem we're experiencing with each & every distro is the mouse/touchpad freezes. In the live version all is OK, then once installed still OK...but only last for a couple of shutdowns & then the above problem kicks in. sometimes after the freeze it may work ok again the next time it is booted but not long before the freeze occurs again.....obviously xinput shows the elantech touchpad is not listed
I know it is a low spec netbook but there are many distros which claim to work on a much lower spec than this. I am not sure if this processor supports PAE as it often mentions PAE not supported on celeron M's but I also read that the pc usually needs to be pre 1995 to not support PAE & this netbook was made around 2008
I must say that most of the distros we've tried seem to be running OK until the 'freeze' put top hat on hit...so I am stumped as to what the issue is and hope some of you more experienced guys can point me in the right direction....i.e. a suitable distro for use on this eeepc netbook. My hubby does nothing fancy on the pc, he's just really browsing, skyping would be nice....OH & he is very computer illiterate....so something simple to use, fast & lightweight is all that is required.
The next distro I was going to try was leeenux linux, which is supposed to be perfect for the eeepc, but the only 2 free versions I could find is version 5.1 extended & v6 lxde SSD 2g
Many thanks in advance !!

Hi

I've build my desktop from scratch a long time ago and it's using the standard BIOS.

I am planning to get a laptop at some time and it has windows 8.1 with UEFI. My plan to to wipe windows off the thing and install linux.

I will be dealing with UEFI for the first time, so my question is, do I need to get an UEFI supported distro or will any linux distro detect the UEFI and install accordingly?

Thanks

I have installed linux(mint and ubuntu) on a few laptops, but i have an ASUS eEEE netbook PC..Atom processor...No DVD drive...

I have chosen PUPPY Linux distro, and I have booted from a thumb a few times to make sure everything seems to work....but...when I start trying to install...well...its asking me about using the partition tool to change the types of partitions that are best for linux...

I am not understanding the instructions...as far as what i need to do...has anybody done this install ,,,the current netbook OS is Windows Starter 7. I just want to REPLACE it entirely with linux puppy. I did not encounter this on my laptop installs..i just said yes...replace the current OS..but somehow the netbook install is acting different....do i need to change the partitions or can i just take the defaults...I forge the exact partition extentsions..something line ntfs and it says to change to ext2 and ext3...not sure how to do that...

Can some direct me to the best way to do this? thx.

Hey guys, I am trying to find the best lightweight OS for my asus eee pc seashell series which I mainly use for programming; nothing heavy of any sort, just simple programs written in c++ and java for projects and stuff, I have my main pc for android studio and whatnot.

I'm currently using windows 7 ultimate 32-bit and it gets quite slow when I'm running netbeans + oracle sql and a couple of documents and web browsers etc.

Specs:
•Intel Atom N570 Dual core
•Intel GMA 3150
•2GB RAM

I have used Ubuntu 2 years ago for about a year, other than that I don't know anything about Linux distros. I have researched a few distros yet still skeptical about satisfying my needs especially the programming part.
Thanks in advance.

I am trying to boot Linux Mint from an 8gb Sandisk USB. I changed my boot settings and it boots into what I believe is called grub? I am given two options, Boot Linux Mint, Boot Linux Mint (compatibility mode). When I select either of them all I get is a black screen. I've tried many things to get around this, messing with my graphics card settings (within grub), different USB's (another 8gb and a 32gb), I tried Ubuntu and that just doesn't boot at all I go straight back to my UEFI settings. I'm very new to Linux and I don't just want to hop in, I just want to boot from my USB whenever I want to play around with it. Thank You

Note: I'm running windows 8.1 currently on a ASUS N550JV laptop. I've been using the UUI from Pen Drive Linux.

First time Linux Mint user and fist time poster to this forum. Need to install a Linux distro on my family member's HP Mini 1000, an older netbook with minimal hardware (1 GB memory stick, Intel Atom N270 processor, 80 GB ATA HDD, and it runs XP SP3. . I advised her to uninstall XP and buy Windows 7, but she doesn't want to spend the $93. So ...

I have been testing different Linux distros from flash drive on my HP Probook 4530S laptop. Have tried Ubuntu 14x and now Mint, which I prefer. Ubuntu wouldn't boot to desktop on the netbook after choosing "Use without installing." Mint runs OK on it, but I can't configure the wireless connection. I suspect that either the network hardware isn't compatible or I am missing something when trying to manually configure the settings. I read some info from the Mint web site about this issue, but not sure about whether the Mini's wireless card is compatible: Broadcom 802.11b/g WLAN. Does updating Windows drivers help with this?

TIA,

Don

I have a new PC and it's my first with a UEFI motherboard. I've been using Manjaro on it for a few weeks but now I want to switch distros. Before UEFI it was easy; I'd just tell the new distro's installer to overwrite / and use the existing /home as /home. But now I have these extra partitions that Manjaro created regarding UEFI and I'm not sure how to go about it.

I just used the Linux Mint USB live disc and launched the installer. The partitioning tool showed me /bios and /EFI in addition to the other partitions that are more familiar to me, like /boot, /, /home and /swap. It would not let me alter the /bios and /EFI partitions.

In order to preserve /home. what should I tell the Mint installer to do? Should I just overwrite /boot and / as I've always done? Will it work like that on a UEFI system? Many thanks in advance for all advice.

Output of fdisk -l:

Quote:
Device Start End Sectors Size Type
/dev/sda1 2048 6143 4096 2M BIOS boot
/dev/sda2 6144 210943 204800 100M EFI System
/dev/sda3 210944 735231 524288 256M Linux filesystem (this is /boot)
/dev/sda4 735232 62175231 61440000 29.3G Linux filesystem (this is /)
/dev/sda5 62175232 1938952191 1876776960 894.9G Linux filesystem (this is /home)
/dev/sda6 1938952192 1953521663 14569472 7G Linux swap

I get kernel panics and computer shut down when trying to install and run Linux Mint 17 Mate and Linux Mint 17.1 on an older HP laptop. The laptop is a Pavilion dv 5140 with 2.0GHz AMD Turion chip, 2.0 Gigs ram and 120GB hard drive. Linux is the only software installed on the computer. Yet, I think my problem is probably related to the hardware? Does anyone have any suggestions or experience with this situation? Thank you.

Wireless mouse and wireless keyboard is not working in Linux distro's.

Read the similar threads on this issue. Boot mode is set for UEFI and Legacy therefore not sure what to do to enable mouse and keyboard? The mouse and keyboard use the same 'receiver' and the receiver indicator is green when Linux distro is fully loaded. Have tried various distro's, Ubuntu, and Ubuntu based distro's using LIVE DVD method on all. Latest distro tried is Peach 14.04.1 TW.40 64 bit. Motherboard is a Gigabyte GA-990FXA-UD3, CPU AMD FX6300 3.5 Ghz six core.

Thanks for any assistance.

jmwrocky

Hello.

I don't know if this forum is the correct one to ask about this problem. Feel free to move it to another forum.

I am running PelicanHPC, a Debian-live based clustering distro.
It sets up a DHCP server, and offer PXE boot to other machines in a network.
I have switch off the DHCP server in my router.

Problem is that when I boot from this computer through the network, it displays a message for a split of a second: Succeed download. I guess that it is downloading the NBP correctly. But then, it's just returning to BIOS and/or booting my OS normally.

The other computer is offering a non-EFI image, and this computer boots: UEFI: PXE IPv4. Maybe there is a mismatch, but I have no idea on how to fix this.

What can I do to boot it correctly?

If you need more information, just ask me about it.

Thank you