Problem Installing Radeon Driver Packages With Second Debian Install

I have a debian OS on a partition on my hard disk (sda1).
There was no sound because the ati rs880/radeon 4200 sound card needed drivers which were only in the debian 'non-free' version'.
So I added the non-free version to my install and also had to make a change to the GRUB bootloader file.
After that, I got sound.

Now I've installed a new debian distro to my second partition - sda2.
This time I ensured I installed the debian non-free version.
But I'm having trouble installing the drivers for the sound card.

I go into Synaptic package manager to install the relevant drivers and it gives me an error message:
Code:
Configuring libfglrx - install Fglrx driver despite unsupported graphics card?

I'm not sure what that means because I want the drivers for my sound card - not graphics.
When I press the 'Help' button, it says:
Code:
This system has a graphics card which is no longer handled by the Fglrx driver...
The above card requires either the non-free legacy Fgrlx driver 
(package fgrlx-legacy-driver) or the free Radeon driver (package xserver-xorg-video-radeon).

This is fine because I can just install the 'free Radeon driver'.

But the Help message then says:
Code:
Before the Radeon driver can be used you must remove Fglrx configuration from xorg.conf 
(and xorg.conf.d/)
Note that switching to the free Radeon driver requires the fglrx-driver package to be purged (not just removed).

So now I don't know what to do. Has anyone had this error message?
I know I can enable sound and have no problems with the graphics card because that's what happened with my original install on sda1.

But with the install on sda2, I don't know how to approach this problem.
Can anyone help please?


Similar Content



Mint 17 Cinnamon Failed, Stuck In Fallback (likely Caused By Graphics Driver Install)

Hi LQ,
I am currently experiencing an issue on a fresh install of Mint 17.1 Cinnamon in which I am permanently stuck in fallback mode (that is, unless I hard shutdown or reboot) on an aging laptop with AMD Radeon HD 4200 graphics (considered legacy). I believe this issue was caused by a failed install of AMD's latest linux graphics drivers, in which I literally opened the .run file and attempted to install. The install failed (some error), of course, but when I rebooted, I was kicked into fallback. After some googling, I autoremoved fglrx then installed fglrx, as I read would reinstall fglrx, the proprietary drivers for AMD cards and rebooted. Still stuck in fallback. I removed and installed Xorg and rebooted. Still stuck in fallback. I downloaded the AMD legacy drivers from AMD's site (my card's series included with this set). Had to change the permissions to run this .run file but eventually ran it from terminal, but this install also failed (claimed I was missing tool(s), despite not indicating precisely what I was missing). I'm still rummaging around for fixes, but maybe asking can help. I can provide some more info below, but let me know what else you need (and how to get it) if you wish to help. I really want linux to work out for me instead of shelling out $$ for Windows, but so far this has been a rocky start. Thanks


Code:
inxi -G

yields
Code:
Graphics:   Card: AMD RS880M [Mobility Radeon HD 4225/4250]
X.Org: 1.15.1
drivers: fbdev,ati,radeon (unloaded: fglrx,vesa)
Resolution: 1024x768@76hz
GLX Renderer: N/A
GLX Version: N/A


Code:
lshw -C video

yields
Code:
*-display UNCLAIMED
description: VGA compatible controller
product: RS880M [Mobility Radeon HD 4225/4250]
vendor: AMD
physical id: 5
...(bunch of stuff on specs)

Have also did apt-get update and apt-get dist-upgrade.
Still no luck, let me know what you think.

Install Fglrx Driver Instead The Open Source Radeon In Debian 7?

Hello, my video card "Advanced Micro Devices [AMD] nee ATI Cedar PRO [Radeon HD 5450/6350]"
create something which can be seen with dmesg "drm: registered panic notifier".
Should I install the fglrx driver instead of keeping the open source radeon as per current install?
I have antix which is a debian wheezy based system https://wiki.debian.org/ATIProprietary# ... 2Wheezy.22
Thanks for any advice before I do it.

No System Sound Setting On Debian With Xfce Desktop

I have installed a new Debian OS to try out the xfce desktop.
My radeon hdmi sound card needs non-free drivers and so I have no sound.
On my previous debian install with gnome desktop, I found a number of changes I had to make to get the sound working.

I have done all this with this new install with xfce.
However, one thing I haven't done yet is to change the System settings-Sound settings to use the hdmi sound card.
The problem is the xfce desktop doesn't have an icon for sound settings under System settings.

This is a bit weird. So I'm wondering if xfce has installed correctly or if it's missing a package so the System sound settings will show up.
Does anyone know what's going on?

New Debian 7.7 Non-free Install - Sound Not Working.

Hello everyone.
I have just installed debian stable non-free onto my hard drive but the sound isn't working.

I've been to the debian site https://wiki.debian.org/SoundConfiguration and found that 'users' don't automatically have access to audio (for security reasons).
So I did the following command as root (sudo):
Code:
adduser USER_NAME audio

Now when I am 'user', I can get sound.

I also did:
Code:
chgrp cdrom /dev/sr0
adduser USER_ID cdrom

This allows 'user' to get sound from the cdrom.

I then went onto the debian soundfaq https://wiki.debian.org/SoundFAQ

From the 'lspci -v' command, I get these 2 outputs which have the word 'audio' in it:
Code:
01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS880 HDMI Audio [Radeon HD 4200 Series]
	Subsystem: Giga-byte Technology Device 960f
	Flags: bus master, fast devsel, latency 0, IRQ 19
	Memory at fdefc000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: snd_hda_intel

00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
	Subsystem: Giga-byte Technology Device a102
	Flags: bus master, slow devsel, latency 32, IRQ 16
	Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: snd_hda_intel

So I have 2 sound cards.

The debian website says: 'If sound does not work for root account as well, then that means that either your sound card is not supported by Debian or it was not configured properly'.

Ok, so the first part of the statement is worrying.
So I went to the debian device driver check page http://kmuto.jp/debian/hcl/ and did 'lspci -n'.
The output can be pasted onto their web page and debian will say if the sound cards are supported.
The web page shows that the sound cards are supported:

Quote:
10024383 Yes Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) snd-hda-intel v2.6.25
10029715 Yes Advanced Micro Devices [AMD] nee ATI RS880 [Radeon HD 4250] radeon v2.6.35-
1002970f Yes Advanced Micro Devices [AMD] nee ATI RS880 HDMI Audio [Radeon HD 4200 Series] snd-hda-intel v2.6.27-
So now I'm guessing that my sound cards are 'not configured properly'. But I've run a Youtube video and then changed the sound cards under alsamixer and I still don't get sound.
Is there is a simple solution to this please? Thank you in advance.

No Sound On Debian Live Usb Using Pavucontrol And ATI RS880 [Radeon HD 4200] Audio

Hello everyone.
The sound isn't working on my debian live usb.
I've installed pavucontrol hoping that this would turn on the sound somehow. But it hasn't.

The program is showing RS880 HDMI audio [Radeon HD 4200] as my output device.
The play back bar moves when I play video on youtube but there is no sound.
On the configuration tab, I've tried all the options under 'built-in audio' - but none of these seem to work.


aplay -l

Code:
 
**** List of PLAYBACK Hardware Devices ****
card 0: SB [HDA ATI SB], device 0: ALC892 Analog [ALC892 Analog]
  Subdevices: 0/1
  Subdevice #0: subdevice #0
card 0: SB [HDA ATI SB], device 1: ALC892 Digital [ALC892 Digital]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
  Subdevices: 0/1
  Subdevice #0: subdevice #0

Don't know why there are 3 playback devices...

lspci | grep -i audio

Code:
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS880 HDMI Audio [Radeon HD 4200 Series]

Not sure why there appears to be two sound cards...

On a Ubuntu site about a similar problem with the same sound card, they suggest creating /etc/asound.conf and adding code to it http://ubuntuforums.org/showthread.php?t=1647400
However, at this point, I'm a bit lost.
Can someone help please?

How To Recover From A Botched Graphics Card Driver Install

OK,

Lastnight I decided to finally attempt to install the dedicated ATI/AMD Catylist drivers. After all I was successfull with the HP drivers, right...

No matter which grub selection I make, getting in is broken, except of course for the Windows XP Pro x64 entry, that works just fine. I'm here with you today, because of the Fedora 21 Live DVD, (slooooww).

Here is the drivers log file:

==========================================================
Supported adapter detected.
Check if system has the tools required for installation.
Uninstalling any previously installed drivers.
Unloading radeon module...
rmmod: ERROR: Module radeon is in use
Unloading drm module...
rmmod: ERROR: Module drm is in use by: ttm drm_kms_helper radeon
[Message] Kernel Module : Trying to install a precompiled kernel module.
[Message] Kernel Module : Precompiled kernel module version mismatched.
[Message] Kernel Module : Found kernel module build environment, generating kernel module now.
AMD kernel module generator version 2.1
doing Makefile based build for kernel 2.6.x and higher
rm -rf *.c *.h *.o *.ko *.a .??* *.symvers
make -C /lib/modules/3.18.3-201.fc21.x86_64/build SUBDIRS=/usr/lib/modules/fglrx/build_mod/2.6.x modules
make[1]: Entering directory '/usr/src/kernels/3.18.3-201.fc21.x86_64'
CC [M] /usr/lib/modules/fglrx/build_mod/2.6.x/firegl_public.o
/usr/lib/modules/fglrx/build_mod/2.6.x/firegl_public.c:6396:12: warning: ‘KCL_fpu_save_init’ defined but not used [-Wunused-function]
static int KCL_fpu_save_init(struct task_struct *tsk)
^
CC [M] /usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o
/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.c: In function ‘KCL_ACPI_Slot_No_Hotplug’:
/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.c:845:21: error: ‘struct acpi_device_flags’ has no member named ‘no_hotplug’
tdev->flags.no_hotplug = true;
^
scripts/Makefile.build:257: recipe for target '/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o' failed
make[2]: *** [/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o] Error 1
Makefile:1385: recipe for target '_module_/usr/lib/modules/fglrx/build_mod/2.6.x' failed
make[1]: *** [_module_/usr/lib/modules/fglrx/build_mod/2.6.x] Error 2
make[1]: Leaving directory '/usr/src/kernels/3.18.3-201.fc21.x86_64'
Makefile:88: recipe for target 'kmod_build' failed
make: *** [kmod_build] Error 2
build failed with return value 2
[Error] Kernel Module : Failed to compile kernel module - please consult readme.
[Reboot] Kernel Module : dracut
==========================================================

I just rebooted without attempting to configure the card, as per the ATI/AMD warning stating that it's important to do so, because my thinking was derailed due to seeing errors, and the install program said I needed to reboot. Afterall, I just couln't believe that with a "Failed to compile kernel module" error, it would actually keep the changes I'd made, that surely Linux had a failsafe in place for such circumstances. In other words, I'm also a newbie, and just don't know how many hoops of fire one has to jump through to be at peace with linux.

Can anyone please help be get back into my install, I've already set up so many things, there's just got to be a way, right?


Thanks in Advance!


JustAnotherHuman

How Can I Activate My Wireless?

Install Ethernet, Intel 4965AGN 802.11abgn

Postby xpdin on Fri May 15, 2015 6:53 am
Hi,

I can't set my wireless anymore like before with the next command,

Code: Select all
sudo apt-get install bcmwl-kernel-source



Can someone help me please?

The new log for

Code: Select all
inxi -Fxz

is:

xpd@Multix ~ $ inxi -Fxz
System: Host: Multix Kernel: 3.13.0-37-generic i686 (32 bit, gcc: 4.8.2)
Desktop: Xfce 4.11.6 (Gtk 2.24.23) Distro: Linux Mint 17.1 Rebecca
Machine: System: Hewlett-Packard (portable) product: N/A version: F.09
Mobo: Hewlett-Packard model: 30D7 version: KBC Version 83.12
Bios: Hewlett-Packard version: 68MDD Ver. F.09 date: 01/11/2008
CPU: Dual core Intel Pentium Dual CPU T2390 (-MCP-) cache: 1024 KB flags: (lm nx sse sse2 sse3 ssse3) bmips: 7447.96
Clock Speeds: 1: 800.00 MHz 2: 1600.00 MHz
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV516/M62-S [Mobility Radeon X1350] bus-ID: 01:00.0
X.Org: 1.15.1 drivers: ati,radeon FAILED: fbdev,vesa Resolution: 1152x864@60.0hz
GLX Renderer: Gallium 0.4 on llvmpipe (LLVM 3.4, 128 bits) GLX Version: 2.1 Mesa 10.1.3 Direct Rendering: Yes
Audio: Card: Intel 82801H (ICH8 Family) HD Audio Controller driver: snd_hda_intel bus-ID: 00:1b.0
Sound: Advanced Linux Sound Architecture ver: k3.13.0-37-generic
Network: Card-1: Broadcom BCM4311 802.11a/b/g driver: b43-pci-bridge bus-ID: 10:00.0
IF: N/A state: N/A mac: N/A
Card-2: Intel 82562GT 10/100 Network Connection driver: e1000e ver: 2.3.2-k port: 5000 bus-ID: 00:19.0
IF: eth0 state: down mac: <filter>
Drives: HDD Total Size: 250.1GB (1.7% used) 1: id: /dev/sda model: Hitachi_HTS54252 size: 250.1GB
Partition: ID: / size: 49G used: 4.1G (9%) fs: ext2 ID: swap-1 size: 40.00GB used: 0.00GB (0%) fs: swap
RAID: No RAID devices detected - /proc/mdstat and md_mod kernel raid module present
Sensors: System Temperatures: cpu: 48.0C mobo: 27.9C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 141 Uptime: 2 min Memory: 191.2/2015.6MB Runlevel: 2 Gcc sys: 4.8.2 Client: Shell inxi: 1.8.4
xpd@Multix ~ $


Thank you very much.

Can't Open Pavucontrol In Xfce - Sound Not Configured

I am trying to open pavucontrol in debian with the xfce desktop.
The error message is:

Code:
Connection to Pulseaudio failed. Automatic retry in 5s
In this case this is likely because PULSE_SERVER in the Environment/X11 Root Windows Properties or default-server in client.conf is misconfigured.

I am having trouble getting sound and configuring the settings.
There is no sound setting in the Settings Manager of xfce.
Also, every time I change alsamixer to my hdmi sound card it keeps going back to the default analog sound card when I exit the program.

How can I access the system settings on the desktop or do I need to change a file setting from the terminal?

Error When Installing AMD Catalyst Driver

I am suffering occasional disturbances in Libre Writer. Writing can disappear at times or appear where it is not supposed to be. I have tried installing drivers for my Sapphire Radeon GPU but get ¨One or more of the tools required for installation cannot be found on the system¨ i have tried many things using sudo apt-get that people have suggested, but no success. The driver i have downloaded is the only one that came up in the search on AMD (the Sapphire site tried to send me there (got a 404 but worked out it was just the ati support site judging by url))

Specs:
PCLinuxOS KDE 64-bit fully updated
Custom PC (Asus A8R32 MVP ´board)
CrossFireX 2x Sapphire Radeon HD 3870
AMD Athlon 64 X2 Dual core 4200+ (i think, no sticker but says at boot)

thanks, ZZII

No Sound

I am getting no response from my speakers. I'm not sure if xubunto has install my sound card device driver correctly. Running xubuntu under vmware player.