Problem With Nvidia Chipset

new computer from boxes, does not install nvidia driver
Booted from USB then ran YaST, I am new with OpenSuse but have two times before installed OpenSuse on fresh HDD's and Nvidia cards with ease.

The symptoms are like when I switched from a GTX 640 that only has mother board power to the GTX 750 Ti and needed power that I did not connect at first. Until I added extra power to the graphics card I only got a single low res VGA output. This 750 card definitely has power but still can only provide single low res to VGA output.

Terminal (dmesg) ......The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1380)installed in this system is not supported by the 304.125 NVIDIA Linux driver release. Please see 'Appendix A - supported NVIDIA GPU Products' in this release's README, available on the Linux driver download page at www.nvidia.com. .... None of the VVIDIA graphics adapters were initialized!

Terminal (uname -r) 3.16.7-21 -default [OpenSuse version]

Terminal (/sbin/lspci) VGA Compatible controller: Nvidia Corporation GM107 [GeForce GTX 750 Ti] (rev 02)

have tried:
1. different power cables to graphic card
2. two GTX 750 Ti cards, neither work.
3. re-installed OpenSuse
4. removed card and mother board can run two monitors in high res. DVI cables are new and work. Monitors (4) are all AOC i2367 and working.

5. added to repository 'bumblebee' which contains NVIDIA drivers and tried rebooting. I am not good at repositories yet. However, I didn't need to do this twice before on new installs with NVIDIA cards.

6. downloaded from www.geforce.com file:///home/shark/Downloads/NVIDIA-Linux-x86_64-346.72(1).run but when I run it error, "The file /home/shark/Downloads/NVIDIA-Linux-x86_64-346.72(3).run was opened with UTF-8 encoding but contained invalid characters."It is set to read-only mode, as saving might destroy its content.
Either reopen the file with the correct encoding chosen or enable the read-write mode again in the menu to be able to edit it."

Hardware list: Asus H81M-E motherboard, i5 4460 CPU, 550W power, Asus GeForce GTX 750 Ti graphic card,

Note: two graphic cards on hand, both work in another OpenSuse computer.

I am just learning Linux so I need simple step by step instructions.

Thank you in advance.

Hello everyone im new here and it is my first post, im using slackware 14.1 x64 on an alienware m11xR2 and im havin trouble with Nvidia drivers.

I tried binary and package installations with bumblebee.

Nothing works, GLX doesn't work and after making "nvidia-xconfig" X doesn't start.

I remove the xorg.conf and then X starts but without nvidia and GLX.

Can someone help me ?

Oh, and im french so sorry for my bad english.

Hey guys. So I just went out and bought a Sager 8268-s (clevo p150sm-a) With an i7 4910mq and a Nvidia 980m gt. As I am a computer tech by trade, every time i see Windows i get horrible PTSD so i decided to try Linux instead. After many hours of trying to get a dual boot working finally got Linux Mint 17 Cinnamon installed on my computer, but when I went to install the Nvidia driver it landed me in fallback mode which I could not escape. So then I tried Ubuntu 14.04 LTS thinking maybe Mint was incompatible with the driver and the same thing happened.

So here is my method:

(sorry i don't know how to make a code box :/ )

First I log in to get root access:

$ su

Then I Update the xorg:

$ sudo apt-add-repository ppa:xorg-edgers/ppa

Then update my system:

$ sudo apt-get update && sudo apt-get dist-upgrade

Then i go into Virtual terminal (Ctrl+Alt+F1) and disable the display manager:

$ sudo service mdm (or lightdm for Ubuntu) stop

Then i install the drivers which i have done multiple ways:

$ sudo apt-get install nvidia-current nvidia-settings

or

$ sudo apt-get install nvidia-343 nvidia-settings

or by downloading the driver from Nvidia (first designating the file as executable)

$ sudo sh nvidia.run && sudo apt-get install nvidia-settings

Then after install, I create the config file:

$ sudo nvidia-xconfig

Then I reboot. After I get the low res mode in Ubuntu or fallback mode in Mint and Driver manager doesn't detect any proprietary drivers and I have to reinstall to get the OS working again. Any suggestions would be greatly appreciated.

Hi everybody!

I have visited this forum a lot in the last years to learn information about Linux, so above all thank you very much to the linuxquestions.org community for building this valuable resource!

Now my question:

I have a brand new Nvidia GTX750 graphics card. Nouveau does not work correctly with this card (very low resolution and red dots all around the screen appear), so I need to install propietary drivers.

I have coped with this when installing distros in my hard drive, I just install the propietary drivers following the reccomended user guidelines and that's all, but I'm now starting to work with Tails (amnesic Linux distribution) and 'unfortunately' as it's an amnesic system I'll have to install them everytime I boot.

I was wondering if there's a way to install them permanently on my Live CD/USB so I am ready to work as soon as I boot. I have not really any clue on how a LiveUSB is composed, and as far as I have searched on the Internet I have not found any information about this matter.

Sorry for the bad grammatics, I have a pretty bad level of English

TL;DR: How can I permanently install Nvidia propietary drivers on an amnesic Linux Live CD/USB?

Regards,

tete7

Hi folks,

I'm trying to install the drivers for my "legacy" nvidia graphics card.
I've downloaded the file from nvidia's website to install the driver, but during the process I get this message...

Kernel header file ' /lib/modules/3.13.0-37-generic/build/include/linux/version.h ' does not exist .

The most likely reason is the kernel source files in ' /lib/modules/3.13.0-37-generic/build ' have not been configured.

Anyone know how to configure this file? I've been working on this for a few days now...it's getting old!

Thanks for your help.

Joe

I recently installed elementaryOS and everything was working fine until I changed the drivers in the Additional Drivers section.
I then tried changing back to the drivers previously used and others but to no avail. I can see the menu bar at the top and run applications, but the whole desktop just appears black.

Here is some info.

Code:

01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 310] (rev a2)

  *-display               
       description: VGA compatible controller
       product: GT218 [GeForce 310]
       vendor: NVIDIA Corporation
       physical id: 0
       bus info: pci@0000:01:00.0
       version: a2
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress vga_controller bus_master cap_list rom
       configuration: driver=nvidia latency=0
       resources: irq:44 memory:fa000000-faffffff memory:d0000000-dfffffff memory:ce000000-cfffffff ioport:ec00(size=128) memory:fbe80000-fbefffff
[1]+  Done                    lspci | grep --color=auto VGA

How can I fix this issue?

Hey everybody!
I am (quite) new to the world of linux, but have been trying out a few of the most basic distros (ubuntu-based ones).
I am now using elementary os luna, and i have a problem with installing my nvidia drivers.
I have really been googling my ass off to find this on my own, but without any results that actually worked for me.
So, i have a HP Envy laptop, with a geforce gt 740m, and i have searched nvidias homepage to find out that the up-to-date driver for me would be the 346 driver. I tried it on Linux mint xfce, and i successfully installed it. I had to add the xorg ppa repository of course, and updated it as well, but when i do the same procedure here on my elementary os, i cant reach the login screen after my reboot.

When i use the lspci -vnn command in the terminal, i get this info on my graphics driver:

01:00.0 3D controller [0302]: NVIDIA Corporation GK208M [GeForce GT 740M] [10de:1292] (rev a1)
Subsystem: Hewlett-Packard Company Device [103c:1961]
Flags: fast devsel, IRQ 16
Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
Memory at a0000000 (64-bit, prefetchable) [size=256M]
Memory at b0000000 (64-bit, prefetchable) [size=32M]
I/O ports at 4000 [size=128]
Expansion ROM at b2000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel modules: nouveau, nvidiafb

I really hope someone knows how to fix my problem.
Thanks in advance!
/Andreas

So I've got 14.04 installed on a new computer I just built. All new hardware, new install, everything new. I had it all up and running for a few days. I got the nvidia drivers installed, installed steam and was even able to play some games. The last time I had it up it loaded fine, I played 'The Talos Principle', then rebooted to go back to windows. Now when I boot into linux it hangs after the login screen. You can look at my post history as I had this issue before. I was able to fix it that time, but I think it was a different cause.

Some things I've tried to date:
The most common suggestion I've found from googling this issue is to restart lightdm. I've done that to no avail.

I've tried simply entering tty from the frozen screen and then coming back out with Ctrl+Alt+F7. No dice there either.

I've also seen that some people needed to reset their graphics drivers when using nvidia. I tried to do that and I don't think it worked. When I try to purge all nvidia packages it always says "0 upgraded, 0 newly installed, 0 to remove and 16 not upgraded".
Results of dpkg:
Code:

$ dpkg -l nvidia*
Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait-Trig-pend
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name           Version      Architecture Description
+++-==============-============-============-===================
un  nvidia-common  <none>       <none>       (no description available)
un  nvidia-prime   <none>       <none>       (no description available)

I'm gonna keep googling around in case I find something useful, but I fear I'm treading into water deeper than I know how to swim in and I'm worried that I'll screw something up if I start experimenting. I know just enough about linux to be dangerous. Any advice on what the results of dpkg above mean or suggestions about the problem would be much appreciated.

edit: Forgot to mention that the last time it was working I didn't make any changes to anything. I played a game and rebooted. Suddenly things are broken.

These instructions originate from https://www.linkedin.com/pulse/20140...nvidia-drivers, but I modified them slightly for my desktop environment (64-bit HP Envy Phoenix 810-135qe w/Intel i7-4770 and HP ZR2440w monitor, nVidia GeForce GTX645, Red Hat Enterprise Linux 7.1 w/Gnome3).

The following procedures replace the nouveau drivers with kmod-nvidia drivers from ElRepo.

Install the repository ElRepo from: http://elrepo.org/tiki/tiki-index.php

Install the package nvidia-detect from within Applications>SystemTools>Software

From within the terminal, enter the command nvidia-detect.
Example:
[anthony@hp810135qe ~]$ nvidia-detect
Output is...
Probing for supported NVIDIA devices...
[10de:11c4] NVIDIA Corporation GK106 [GeForce GTX 645 OEM]
This device requires the current 346.59 NVIDIA driver kmod-nvidia

For my system the following software packages will apply (yours maybe slightly different, the key is to note the ###.## version identified for your system using nvidia-detect as explained above): kmod-nvidia-346.59-1.el7.elrepo (64-bit), nvidia-x11-drv-32bit-346.59-1.el7.elrepo (64-bit), nvidia-x11-drv-346.59-1.el7.elrepo (64-bit)

Now do the following steps in the sequence indicated:

1. Disable X Windows

a) open a terminal and "su" or "sudo -i"

b) ln -fs /lib/systemd/system/multi-user.target /etc/systemd/system/default.target

Note: Another way to disable X Windows is to do the following from within the Terminal # systemctl set-default multi-user.target

To later change back to booting into graphical mode, substitute 'graphical.target' for 'multi-user.target' in the above commands.

c) reboot

2. Remove Nouveau

a) rpm -e xorg-x11-drivers xorg-x11-drv-nouveau

Note: Another way to remove Nouveau is to do the following from within the Terminal

$ yum remove xorg-x11-drivers xorg-x11-drv-nouveau xorg-x11-glamor

See http://elrepo.org/tiki/kmod-nvidia which discusses that glamor still causes a conflict with nVidia in RHEL 7

3. Blacklist Nouveau

a) edit /etc/modprobe.d/blacklist.conf and add line:

blacklist nouveau

Note: A way to edit this file is by doing the following:

# vi /etc/modprobe.d/blacklist.conf
(use INSERT key to make changes in vi; add the line

blacklist nouveau

Hit Esc key to escape INSERT mode, then hit SHIFT Z Z to save and exit with the changes. Hitting :q ENTER leaves vi without saving changes.

b) edit /etc/default/grub and append to GRUB_CMDLINE_LINUX:

rd.driver.blacklist=nouveau

Note: A way to edit this file is by doing the following:

# vi /etc/default/grub and append to GRUB_CMDLINE_LINUX:
(use INSERT key to make changes in vi; add the line

rd.driver.blacklist=nouveau

Hit Esc key to escape INSERT mode, then hit SHIFT Z Z to save and exit with the changes. Hitting :q ENTER leaves vi without saving changes.

IMPORTANT NOTE IF YOU HAVE AN ENCRYPTED BOOTUP DRIVE -

If you have an encrypted root drive, remove "rhgb" from GRUB_CMDLINE_LINUX. This will allow you to interact with the encryption passphrase prompt, since Plymouth doesn't seem to run without a framebuffer friendly video driver loaded. IF YOU DON'T THIS, WHEN YOU BOOTUP YOU WILL GET STUCK AT A BLINKING CURSOR AND BLACKSCREEN THAT HAS THE FOLLOWING ERROR MESSAGES:


[5.757276] scsi 7:0:0:0: alua: not attached
[5.759625] sd 7:0:0:0: [sdg] no caching made page found
[5.759668] sd 7:0:0:0: [sdg] assuming drive cache: write through

WHEN THIS HAPPENS IT MEANS PLYMOUTH IS NOT ABLE TO SHOW YOU THE PROMPT FOR ENTERING THE PASSPHRASE FOR THE ENCRYPTED DRIVES. WITHOUT THE PROMPT THE SYSTEM CAN'T ACCEPT THE PASSPHRASE AND YOU ARE STUCK. IF THIS HAPPENS TO YOU, YOU CAN DO CTRL-ALT-DELETE TO REBOOT - THIS ALLOWS YOU TO HIT 'e' AT THE KERNEL LINE IN GRUB TERMINAL TO EDIT (MOST LIKELY THE TOP KERNEL) AND THEN REMOVE 'rhgb' (which stands for Red Hat Graphical Bootsplashcreen or something like that). WHEN DONE HIT THE KEYS 'CTRL X' TO REBOOT - YOU'LL THEN SEE TEXT MESSAGES SCROLLING AND GET AN OPPORTUNITY TO ENTER THE PASSPHRASE. ENTER THE PASSPHRASE AND YOU SHOULD BE GOOD TO GO.

4. Reconfigure the grub.cfg files

Two options for booting nowadays are BIOS and EFI

-If you chose BIOS boot run this command:
# grub2-mkconfig -o /boot/grub2/grub.cfg
Note: I also have this one being auto-updated-configured in my system (?why? It's EFI).

-If EFI boot on CentOS:
# grub2-mkconfig -o /boot/efi/EFI/centos/grub.cfg

-If EFI boot on RHEL:
# grub2-mkconfig -o /boot/efi/EFI/redhat/grub.cfg
Note: Mine is an EFI system. But I did both this and the BIOS grub.cfg above since it too is being updated by RHEL updates concurrently with the EFI grub.cfg

5. Reboot and Install NVidia Driver - I use ElRepo's kmod-nvidia for this step.

Steps by me to install ElRepo's kmod-nvidia (You should still be in Text mode at this time):

If in multi-user.target mode (text, runlevel 3), then do the following
$ su -
enter root password
# yum install kmod-nvidia - version from above
# yum install nvidia-x11-drv-32bit - version from above (this is for 32bit compatibility)
# yum install nvidia-x11-drv - version from above (this is for Open GL X11 display driver and to be done if kmod didn't already include doing it with the kmod-nvidia installation above)
# exit
$

If still in graphics.target mode (you shouldn't be but if you are) (GUI, runlevel 5),
Use Applications > Software > kmod-nvidia - version from above
Install kmod-nvidia - version from above
Install nvidia-x11-drv-32bit - version from above (this is for 32bit compatibility)
Install nvidia-x11-drv - version from above (this is for Open GL X11 display driver)

6. At this point rebuild initramfs. This recreates initrd w/o nouveau. The existing initrd still has the embedded nouveau drivers if this step is not performed) :

Back up the current initramfs keeping nouveau
# mv /boot/initramfs-$(uname -r).img /boot/initramfs-$(uname -r)-nouveau.img
Build the new one without nouveau
# dracut /boot/initramfs-$(uname -r).img $(uname -r)

7. Re-Enable X Windows

# systemctl set-default graphical.target

8. Reboot

If you have an encrypted bootup drive, when you bootup you may notice that Plymouth doesn't look so good with its text in a lower resolution and you'll see lines of text scrolling until you get to a stopped cursor waiting for you to enter the passphrase to unencrypt your drive. Maybe eventually there'll be a solution for this to keep things moving with a graphical bootsplash all throughout. Until then, this is a minor inconvenience for me.

Hi I a running Ubunto 12.04 on a HP PC with an onboard intel analaog sound card

(ALC662) and a HDMI connection into my TV.
I use this PC for Mythtv and Kodi using the sound over HDMI which works a treat in MythTV however I cannot get the sound to work on Kodi, Firefox or any other app which I presume is down to misconfigured ALSA setup, I had this working previously but it stopped and I am not sure why, possible updates.


sudo aplay -L lists;

Home directory /home/tomc not ours.
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
hdmi_complete
sysdefault:CARD=Intel
HDA Intel, ALC662 rev1 Analog
Default Audio Device
front:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
Front speakers
surround40:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Digital
IEC958 (S/PDIF) Digital Audio Output
dmix:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
Direct sample mixing device
dmix:CARD=Intel,DEV=1
HDA Intel, ALC662 rev1 Digital
Direct sample mixing device
dsnoop:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
Direct sample snooping device
dsnoop:CARD=Intel,DEV=1
HDA Intel, ALC662 rev1 Digital
Direct sample snooping device
hw:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
Direct hardware device without any conversions
hw:CARD=Intel,DEV=1
HDA Intel, ALC662 rev1 Digital
Direct hardware device without any conversions
plughw:CARD=Intel,DEV=0
HDA Intel, ALC662 rev1 Analog
Hardware device with all software conversions
plughw:CARD=Intel,DEV=1
HDA Intel, ALC662 rev1 Digital
Hardware device with all software conversions
hdmi:CARD=NVidia,DEV=0
HDA NVidia, HDMI 0
HDMI Audio Output
hdmi:CARD=NVidia,DEV=1
HDA NVidia, HDMI 0
HDMI Audio Output
hdmi:CARD=NVidia,DEV=2
HDA NVidia, HDMI 0
HDMI Audio Output
hdmi:CARD=NVidia,DEV=3
HDA NVidia, HDMI 0
HDMI Audio Output
dmix:CARD=NVidia,DEV=3
HDA NVidia, HDMI 0
Direct sample mixing device
dmix:CARD=NVidia,DEV=7
HDA NVidia, HDMI 0
Direct sample mixing device
dmix:CARD=NVidia,DEV=8
HDA NVidia, HDMI 0
Direct sample mixing device
dmix:CARD=NVidia,DEV=9
HDA NVidia, HDMI 0
Direct sample mixing device
dsnoop:CARD=NVidia,DEV=3
HDA NVidia, HDMI 0
Direct sample snooping device
dsnoop:CARD=NVidia,DEV=7
HDA NVidia, HDMI 0
Direct sample snooping device
dsnoop:CARD=NVidia,DEV=8
HDA NVidia, HDMI 0
Direct sample snooping device
dsnoop:CARD=NVidia,DEV=9
HDA NVidia, HDMI 0
Direct sample snooping device
hw:CARD=NVidia,DEV=3
HDA NVidia, HDMI 0
Direct hardware device without any conversions
hw:CARD=NVidia,DEV=7
HDA NVidia, HDMI 0
Direct hardware device without any conversions
hw:CARD=NVidia,DEV=8
HDA NVidia, HDMI 0
Direct hardware device without any conversions
hw:CARD=NVidia,DEV=9
HDA NVidia, HDMI 0
Direct hardware device without any conversions
plughw:CARD=NVidia,DEV=3
HDA NVidia, HDMI 0
Hardware device with all software conversions
plughw:CARD=NVidia,DEV=7
HDA NVidia, HDMI 0
Hardware device with all software conversions
plughw:CARD=NVidia,DEV=8
HDA NVidia, HDMI 0
Hardware device with all software conversions
plughw:CARD=NVidia,DEV=9
HDA NVidia, HDMI 0
Hardware device with all software conversions

aplay -D plughw:1,7 /home/tomc/adios.wav will play my sample wav file though the

HDMI.


Heres my /etc/asound.conf


pcm.hdmi_hw {
type hw
card 1 # <--- card number
device 7 # <--- device number
}

pcm.hdmi_complete {
type softvol
slave.pcm hdmi_hw
control.name hdmi_volume
control.card 1
}

pcm.!default hdmi_complete


Any help would be greatly appreciated as I dont fully understand ALSA and its

driving me up the wall :-)

Thanks
TomC