I am totally new to Linux. However, considering the many advantages of the operationg comparing to other OS, i have decided to go ahead with using MINT Rebacca which is the latest version. Initially for some time i did not have any issues in getting my internet connecton. However, for the last one week I am unable to connect through. The results of various terminal commands i applied is given below with a sincere trust somebody would be there to help me out.
-----
anil@anil-HP-15-Notebook-PC ~ $ iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thrff Fragment thrff
Power Managementn
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ ifconfig
eth0 Link encap:Ethernet HWaddr f8:a9:63:90:62:b1
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:149 errors:0 dropped:0 overruns:0 frame:0
TX packets:149 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10689 (10.6 KB) TX bytes:10689 (10.6 KB)
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ ifconfig
eth0 Link encap:Ethernet HWaddr f8:a9:63:90:62:b1
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:149 errors:0 dropped:0 overruns:0 frame:0
TX packets:149 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10689 (10.6 KB) TX bytes:10689 (10.6 KB)
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ lshw -C network
WARNING: you should run this program as super-user.
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:08:00.0
logical name: eth0
version: 07
serial: f8:a9:63:90:62:b1
size: 10Mbit/s
capacity: 100Mbit/s
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8106e-1_0.0.1 06/29/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s
resources: irq:57 ioport:4000(size=256) memory:b5600000-b5600fff memory:b5400000-b5403fff
*-network DISABLED
description: Wireless interface
product: RT3290 Wireless 802.11n 1T/1R PCIe
vendor: Ralink corp.
physical id: 0
bus info: pci@0000:0a:00.0
logical name: wlan0
version: 00
serial: 9c:ad:97:5b:16:45
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=rt2800pci driverversion=3.13.0-37-generic firmware=0.37 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn
resources: irq:16 memory:b5510000-b551ffff
WARNING: output may be incomplete or inaccurate, you should run this program as super-user.
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ lshw -C
Hardware Lister (lshw) - B.02.16
usage: lshw [-format] [-options ...]
lshw -version
-version print program version (B.02.16)
format can be
-html output hardware tree as HTML
-xml output hardware tree as XML
-short output hardware paths
-businfo output bus information
options can be
-class CLASS only show a certain class of hardware
-C CLASS same as '-class CLASS'
-c CLASS same as '-class CLASS'
-disable TEST disable a test (like pci, isapnp, cpuid, etc. )
-enable TEST enable a test (like pci, isapnp, cpuid, etc. )
-quiet don't display status
-sanitize sanitize output (remove sensitive information like serial numbers, etc.)
-numeric output numeric IDs (for PCI, USB, etc.)
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ rfkill list
0: phy0: Wireless LAN
Soft blocked: yes
Hard blocked: yes
1: hp-wifi: Wireless LAN
Soft blocked: yes
Hard blocked: no
2: hp-bluetooth: Bluetooth
Soft blocked: yes
Hard blocked: no
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ lsusb
Bus 001 Device 003: ID 0bda:5776 Realtek Semiconductor Corp.
Bus 001 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 004: ID 12d1:1505 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard
Bus 002 Device 002: ID 24ae:2000
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
anil@anil-HP-15-Notebook-PC ~ $
anil@anil-HP-15-Notebook-PC ~ $ sudo lsusb
[sudo] password for anil:
Bus 001 Device 003: ID 0bda:5776 Realtek Semiconductor Corp.
Bus 001 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 004: ID 12d1:1505 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard
Bus 002 Device 002: ID 24ae:2000
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
anil@anil-HP-15-Notebook-PC ~ $
Wth regards
Anil Kumar
Hi,
i'm new in kali linux.
i have an issue with the wifi connections.
installing the newwst version of kali from the official website on virtual box.
plug the USB wireless adapter (TP-LINK).
also, i noticed wlan0 on #ifconfig command.
on the network setting configure NAT (also tried with NAT bridged)
my problem is that - i cannot see any wireless networks.
i followed few guides from youtube and here but with no luck.
it show me that i'm wired connected.
i attached screenshot bellow.
please kindly assist me.
additional information:
#airmon-ng start wlan0
when i type #ifconfig, i saw that wlan0 changed to wlan0mon
and with#airodump-ng command on wlan0mon i didn't see any wireless network as well
iwconfig
Quote:
root@kali:~# iwconfig
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thrff Fragment thrff
Encryption keyff
Power Managementff
lo no wireless extensions.
lsmod
Quote:
root@kali:~# lsmod | grep rt
rt2800usb 26222 0
rt2x00usb 17642 1 rt2800usb
rt2800lib 81543 1 rt2800usb
rt2x00lib 46315 3 rt2x00usb,rt2800lib,rt2800usb
mac80211 511777 3 rt2x00lib,rt2x00usb,rt2800lib
cfg80211 425751 2 mac80211,rt2x00lib
crc_ccitt 12347 1 rt2800lib
parport_pc 26287 0
parport 35699 1 parport_pc
usbcore 199549 7 rt2x00usb,ohci_hcd,ohci_pci,rt2800usb,ehci_hcd,ehci_pci,usbhid
lsusb
Quote:
root@kali:~# lsusb
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 003: ID 80ee:0021 VirtualBox USB Tablet
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
ifconfig
Quote:
root@kali:~# ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:27:dc:d0:01
inet addr:192.168.1.22 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fedc:d001/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:68 errors:0 dropped:0 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:7485 (7.3 KiB) TX bytes:4163 (4.0 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1200 (1.1 KiB) TX bytes:1200 (1.1 KiB)
wlan0 Link encap:Ethernet HWaddr 90:f6:52:10:0f:d2
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
iw wlan0 info
Quote:
root@kali:~# iw wlan0 info
Interface wlan0
ifindex 4
type managed
wiphy 1
iwlist scan
Quote:
root@kali:~# iwlist scan
eth0 Interface doesn't support scanning.
wlan0 No scan results
lo Interface doesn't support scanning.
uname -a
Quote:
root@kali:~# uname -a
Linux kali 3.18.0-kali3-amd64 #1 SMP Debian 3.18.6-1~kali2 (2015-03-02) x86_64 GNU/Linux
cat /etc/network/interfaces
Quote:
root@kali:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
thanks
hi guys, ive altered the numbers for security but can someone tell me which one of these is my private ip address for this particular computer? im troubleshooting port forwarding and i want to make sure i have the right private ip address. i know the public one already. i used ifconfig to print this out. there are so many addresses that im not sure which is my private one for this particular computer. thanks
Link encap:Local Loopback
inet addr:133.5.7.1 Mask:255.5.6.2
inet6 addr: ::1/144 Scope:Host
UP LOOPBACK RUNNING MTU:44436 Metric:1
RX packets:26824 errors:0 dropped:0 overruns:0 frame:0
TX packets:26824 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3268828 (3.2 MB) TX bytes:3268828 (3.2 MB)
wlan0 Link encap:Ethernet HWaddr 11:1f:8b:a5:98:c2
inet addr:10.1.1.33 Bcast:11.1.1.293 Mask:242.242.242.0
inet6 addr: fe70::23f:7bff:fea9:38c5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1800 Metric:1
RX packets:244694 errors:0 dropped:0 overruns:0 frame:0
TX packets:247756 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:209624351 (209.6 MB) TX bytes:84885694 (84.8 MB)
Hello
I have problem with creating pptp connection on my centos vps.
VPS is under OpenVZ, so in customer panel i enabled TUN/TAP, PPP and IPSEC.
On my centos 6.5 vps i made changes based on this tutorial
http://www.zedt.eu/tech/linux/settin...os-openvz-vps/
and on windows 7 this
http://www.howtogeek.com/51237/setti...ver-on-debian/
And now, windows 7 is giving me 807 error.
Is this iptables rules are correct ?
Code:
iptables -A INPUT -i venet0 -p tcp --dport 1723 -j ACCEPT
iptables -A INPUT -i venet0 -p gre -j ACCEPT
iptables -t nat -A POSTROUTING -j SNAT --to-source [VPS's IP]
iptables -A FORWARD -i ppp0 -o venet0 -j ACCEPT
iptables -A FORWARD -i venet0 -o ppp0 -j ACCEPT
I have no ppp0 interface, and i have additionally vnet0:0 with external ip, and gre0 and gretap0 interfaces.
So ifconfig -a shows:
Code:
[root@vps ~]# ifconfig -a
gretap0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1476 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
gre0 Link encap:UNSPEC HWaddr 00-00-00-00-FF-FF-80-4B-00-00-00-00-00-00-00-00
NOARP MTU:1476 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255
inet6 addr: 2602:ffc5::ffc5:6f61/128 Scope:Global
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:101201 errors:0 dropped:0 overruns:0 frame:0
TX packets:42319 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:131220862 (125.1 MiB) TX bytes:4717867 (4.4 MiB)
venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:x.x.x.x P-t-P:x.x.x.x Bcast:x.x.x.x
Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
So is vnet0 should be vnet0:0 ?
And what should be instead of ppp0 interface ?
Hi.
This is the first time I need to do this. New to Linux... :-)
I need to have two Ethernet connections in my laptop working. Its Ethernet RJ-45 jack works fine. I had to get a new Trendnet USB/Ethernet adapter for the second connection. After I connected it for the first time to my laptop having Fedora 15, I get:
[root@Brcm-AP brcmapac]# tail -f /var/log/messages
Mar 17 05:31:57 Brcm-AP dbus: [system] Successfully activated service 'org.freedesktop.PackageKit'
Mar 17 05:36:58 Brcm-AP kernel: [11429.615508] TCP lp registered
Mar 17 05:42:35 Brcm-AP kernel: [11766.773200] composite sync not supported
Mar 17 05:46:17 Brcm-AP dbus: [system] Activating service name='net.reactivated.Fprint' (using servicehelper)
Mar 17 05:46:17 Brcm-AP dbus: [system] Successfully activated service 'net.reactivated.Fprint'
Mar 17 05:46:48 Brcm-AP dbus: [system] Activating service name='org.freedesktop.PackageKit' (using servicehelper)
Mar 17 05:46:48 Brcm-AP dbus: [system] Successfully activated service 'org.freedesktop.PackageKit'
Mar 17 06:04:07 Brcm-AP kernel: [13058.324180] composite sync not supported
Mar 17 06:04:49 Brcm-AP dbus: [system] Activating service name='net.reactivated.Fprint' (using servicehelper)
Mar 17 06:04:49 Brcm-AP dbus: [system] Successfully activated service 'net.reactivated.Fprint'
Mar 17 06:06:07 Brcm-AP kernel: [13177.798536] usb 1-5: USB disconnect, address 4
Mar 17 06:06:10 Brcm-AP kernel: [13181.511109] usb 1-5: new high speed USB device using ehci_hcd and address 5
Mar 17 06:06:10 Brcm-AP kernel: [13181.630296] usb 1-5: New USB device found, idVendor=0b95, idProduct=1790
Mar 17 06:06:10 Brcm-AP kernel: [13181.630304] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Mar 17 06:06:10 Brcm-AP kernel: [13181.630311] usb 1-5: Product: AX88179
Mar 17 06:06:10 Brcm-AP kernel: [13181.630316] usb 1-5: Manufacturer: ASIX Elec. Corp.
Mar 17 06:06:10 Brcm-AP kernel: [13181.630320] usb 1-5: SerialNumber: 0000000000103C
Mar 17 06:06:10 Brcm-AP mtp-probe: checking bus 1, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5"
Mar 17 06:06:10 Brcm-AP mtp-probe: bus: 1, device: 5 was not an MTP device
Mar 17 06:09:07 Brcm-AP dbus: [system] Activating service name='org.freedesktop.PackageKit' (using servicehelper)
Mar 17 06:09:07 Brcm-AP dbus: [system] Successfully activated service 'org.freedesktop.PackageKit'
the output does detect the new USB adapter "Product: AX88179, Manufacturer: ASIX Elec Corp.".
The list of interfaces seen:
[root@Brcm-AP brcmapac]# ifconfig
em1 Link encap:Ethernet HWaddr 00:18:8B:B6:97:4D
inet addr:10.10.138.24 Bcast:10.10.139.255 Mask:255.255.254.0
inet6 addr: fe80::218:8bff:feb6:974d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:32846 errors:0 dropped:12285 overruns:0 frame:12
TX packets:15532 errors:0 dropped:0 overruns:0 carrier:0
collisions:5185 txqueuelen:1000
RX bytes:35819763 (34.1 MiB) TX bytes:1346684 (1.2 MiB)
Interrupt:18
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1008 errors:0 dropped:0 overruns:0 frame:0
TX packets:1008 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:78668 (76.8 KiB) TX bytes:78668 (76.8 KiB)
wlan0 Link encap:Ethernet HWaddr 00:1A:92:9FA:A3
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
The first connection is em1 and working fine, but I never see a second ethx interface. I figured I'm missing the driver for it. So, I went to the read me file from the cd, where these files a
- asix.h
- ax88179_178a.c
- Makefile
- readme
The readme instructions for Linux say: you need the kernel sources installed on the machine. Make sure the version of the running kernel must match the installed kernel sources.
1. What are kernel sources and how I can download them for this installation? Please, keep in mind I do not know Linux. This is my first time doing more than just the very basics.
The instructions are called "ASIX AX88179_178A USB 3.0/2.0 Gigabit Ethernet Network Adapter Driver Compilation & Configuration on Linux."
My kernel is 2.6.38.6-26.rc1.fc15.i686.PAE
I have no idea how to start.
Thank you!!!
"yum update" command is not working.
IP information and relevant details below:
-------------------------------------------------------------------------
Here is the error message :
yum update
Loaded plugins: fastestmirror, langpacks
One of the configured repositories failed (Unknown),
and yum doesn't have enough cached data to continue. At this point the only
safe thing yum can do is fail. There are a few ways to work "fix" this:
1. Contact the upstream for the repository and get them to fix the problem.
2. Reconfigure the baseurl/etc. for the repository, to point to a working
upstream. This is most often useful if you are using a newer
distribution release than is supported by the repository (and the
packages for the previous distribution release still work).
3. Disable the repository, so yum won't use it by default. Yum will then
just ignore the repository until you permanently enable it again or use
--enablerepo for temporary usage:
yum-config-manager --disable <repoid>
4. Configure the failing repository to be skipped, if it is unavailable.
Note that yum will try to contact the repo. when it runs most commands,
so will have to try and fail each time (and thus. yum will be be much
slower). If it is a very temporary problem though, this is often a nice
compromise:
yum-config-manager --save --setopt=<repoid>.skip_if_unavailable=true
Cannot find a valid baseurl for repo: base/7/x86_64
------------------------------------------------------------------------
eno16777736: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.8.95 netmask 255.255.252.0 broadcast 192.168.11.255
inet6 fe80::20c:29ff:fe4e:58d9 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:4e:58:d9 txqueuelen 1000 (Ethernet)
RX packets 3498 bytes 356084 (347.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1525 bytes 212794 (207.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 22 bytes 2004 (1.9 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 22 bytes 2004 (1.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
---------------------------------------------------------------------------
Steps taken so far :
1. Change to google DNS -->
2. Edited the CentOS-Base.repo file -->
3. Restarted network services -->
Literally I had search all over the place, till now i could not fix the issue.
Appreciate if someone come forward and help me to rectify this issue.
I recently decided to upgrade from Debian Squeeze to Wheezy. Update seemed to go fine with the exception of the following warning concerning my Broadcom bmc5704 gigabit ethernet cards
Quote:
W: Possible missing firmware /lib/firmware/tigon/tg3_tso5.bin for module tg3
W: Possible missing firmware /lib/firmware/tigon/tg3_tso.bin for module tg3
W: Possible missing firmware /lib/firmware/tigon/tg3.bin for module tg3
No problem I will simply install the missing .bin files after the upgrade. Get the .bin files from the Debian repository and install them using the command "dpkg -i file_name.deb" then ran "apt-get install -f" for good measure. Still nothing, I have downloaded the following files and running that same command for each hoping that this would solve my compatibility issue with no such luck.
Quote:
firmware-bnx2_0.36+wheezy.1_all.deb
firmware-bnx2x_0.36+wheezy.1_all.deb
firmware-linux-nonfree_0.36+wheezy.1_all.deb
firmware-linux-nonfree_0.36+wheezy.1~bpo60+1_all.deb
When I attempt to go into System Preferences > Network I get the message "The system network services are not compatible with this version."
I showed the hardware using the lshw command and here is the entry concerning the ethernet interface
Quote:
#output from lshw command
*-network:0
description: Ethernet interface
product: NetXtreme BCM5704 Gigabit Ethernet
vendor: Broadcom Corporation
physical id: 2
bus info: pci@0000:02:02.0
logical name: eth0
version: 10
serial: 00:13:21:b2:cf:46
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 66MHz
capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.116 duplex=full firmware=5704-v3.41, ASFIPMIc v2.36 ip=XX.XX.XX.154 latency=64 link=no mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:25 memory:fdf70000-fdf7ffff
Network file configuration.
Quote:
# Network file
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address XX.XX.XX.XX
netmask 255.255.255.0
network XX.XX.XX.0
broadcast XX.XX.XX.255
gateway XX.XX.XX.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers XX.XX.XX.XX 8.8.8.8
dns-search XXXXXXX.net
Server is an older HP ProLiant and I am attempting to put Wheezy on it from a direct upgrade from squeeze.
At this point I am stumped. Not sure exactly what to do but it seems like a fairly simple fix. If anyone has any suggestions I would sure appreciate the help. Let me know if you need anything.
I'm running VMWare for school. I need to get Fedora 17 to access the internet through the VM for just two assignments and then I can ignore the existence of Linux until I attempt the NOS120 class again. I have been able to get CentOS and every version of Windows online without an issue.
I've tried NAT, I've tried Bridged, I even pushed the Lan Segment, Host Only, and Custom radio buttons just for fun. I know the protocol here is to post a wiki link to a 500 page thread about the essence of the Linux experience. I even opened those and tried to follow along. Then I would try to do the same thing and nothing matched.
If anyone can tell me how to open Konsole on Centos that would be great as well. It might get me one step further. Also, if you guys ever try to work on your own cars and come to a forum that I frequent I promise not to tell you to read the Factory Service Manual instead of just telling you how to unscrew the oil cap. I promise. Especially if you have a Honda or Acura. I will even tell you all of the steps to reset your Maintenance indicator light.
Here is my ifconfig info:
eth0: flags=4099<UP,Broadcast,Multicast> mtu 1500
ether 00:0c:29:f7:d1:c8 txqueuelen 1000 (Ethernet)
RX
RX
TX
TX
device interrupt 19 base 0x2000
lo:flags=73<Up, Loopback, Running> mtu 16436
inet 127.0.0.1 netmask 255.0.0.0
look txquelen 0 (Local Loopback)
RX Packets 80 bytes 6744 (6.5 Kib)
RX erros 0
TX packets 80 bytes 6744
TX errors.
I just built a linux build (Yocto 1.6 aka 3.10.17 kernel) and in the menuconfig I included the USB_RTL5182 for my USB Ethernet card. How do I determine if it's part of the system?
If I lsusb I get:
Bus 001 Device 002: ID 0bda:8153 Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@ventana:/lib/modules/3.10.17-1.0.0_ga+yocto+ge86e8d6#
However if I lsmod
arc4 1687 2
ath9k 123482 0
ath9k_common 26430 1 ath9k
ath9k_hw 473599 2 ath9k_common,ath9k
ath 22661 3 ath9k_common,ath9k,ath9k_hw
mac80211 381472 1 ath9k
cfg80211 231852 4 ath,ath9k_common,ath9k,mac80211
sky2 54014 0
compat 13931 5 cfg80211,ath9k_common,ath9k,mac80211,ath9k_hw
There is no RL8152 module running. Do I need to somehow bind it? How do I even tell if it's actually installed and my menuconfig didn't screw up somewhere. I'm a total linux noob so figuring out why I have no eth0 is a mystery to me.
Thanks!
Gavin
Hi guys,
I'm new to the forum and the first problem appeared, hope u guys can help me out!
Just changed my system from Windows to Linux and have some issues to get my Wifi Stick
Fritz! WLAN USB N v 2 working.
1. I downloaded the newest drivers for Win64-Bit from the AVM Homepage.
2. Started ndiswrapper Selected the fwlan64.inf -> Clicked on install.
3. Error Message appears :
modprobe: FATAL: Module ndiswrapper not found
4. Uninstalled ndiswrapper (thought probably and older version could fix this was reading on some Ubuntu Forum cause i couldnt find anything for Ziron)
Any help appreciated!
Thank you so much!
Edit: Some more info
System Log:
Quote:
stani-System-Product-Name kernel: [ 2085.487551] usb 2-1.6: USB disconnect, device number 13
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.452762] usb 2-1.6: new high-speed USB device number 14 using ehci-pci
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.549669] usb 2-1.6: New USB device found, idVendor=057c, idProduct=8501
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.549674] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.549677] usb 2-1.6: Product: FRITZ!WLAN USB Stick N v2
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.549680] usb 2-1.6: Manufacturer: AVM Berlin
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.549682] usb 2-1.6: SerialNumber: 246511430F18
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.624607] usb 2-1.6: reset high-speed USB device number 14 using ehci-pci
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.719007] ieee80211 phy4: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.756314] ieee80211 phy4: rt2x00usb_vendor_request: Error - Vendor Request 0x09 failed for offset 0x0000 with error -32
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.756320] ieee80211 phy4: rt2x00lib_probe_dev: Error - Failed to allocate device
Feb 12 16:34:23 stani-System-Product-Name kernel: [ 2086.756349] rt2800usb: probe of 2-1.6:1.0 failed with error -32
Feb 12 16:34:23 stani-System-Product-Name mtp-probe: checking bus 2, device 14: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6"
Feb 12 16:34:23 stani-System-Product-Name mtp-probe: bus: 2, device: 14 was not an MTP device
Feb 12 16:34:24 stani-System-Product-Name usb_modeswitch: switched to 057c:ffffffff on 002/013
uname -a
Quote:
Linux stani-System-Product-Name 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
stani@stani-System-Product-Name:~$
lsusb
Quote:
Bus 002 Device 006: ID 0b05:179c ASUSTek Computer, Inc.
Bus 002 Device 014: ID 057c:8501 AVM GmbH
Bus 002 Device 004: ID 1ea7:1005
Bus 002 Device 003: ID 046d:c326 Logitech, Inc.
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 002: ID 05e3:0727 Genesys Logic, Inc. microSD Reader/Writer
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
i've just installed zorin 9 on my hp 635 notebook.i'm struggling to create wireless from ethernet to share internet with other devices pliz help!