Error When Installing AMD Catalyst Driver

I have a debian OS on a partition on my hard disk (sda1).
There was no sound because the ati rs880/radeon 4200 sound card needed drivers which were only in the debian 'non-free' version'.
So I added the non-free version to my install and also had to make a change to the GRUB bootloader file.
After that, I got sound.

Now I've installed a new debian distro to my second partition - sda2.
This time I ensured I installed the debian non-free version.
But I'm having trouble installing the drivers for the sound card.

I go into Synaptic package manager to install the relevant drivers and it gives me an error message:
Code:

Configuring libfglrx - install Fglrx driver despite unsupported graphics card?

I'm not sure what that means because I want the drivers for my sound card - not graphics.
When I press the 'Help' button, it says:
Code:

This system has a graphics card which is no longer handled by the Fglrx driver...
The above card requires either the non-free legacy Fgrlx driver 
(package fgrlx-legacy-driver) or the free Radeon driver (package xserver-xorg-video-radeon).

This is fine because I can just install the 'free Radeon driver'.

But the Help message then says:
Code:

Before the Radeon driver can be used you must remove Fglrx configuration from xorg.conf 
(and xorg.conf.d/)
Note that switching to the free Radeon driver requires the fglrx-driver package to be purged (not just removed).

So now I don't know what to do. Has anyone had this error message?
I know I can enable sound and have no problems with the graphics card because that's what happened with my original install on sda1.

But with the install on sda2, I don't know how to approach this problem.
Can anyone help please?

Hi LQ,
I am currently experiencing an issue on a fresh install of Mint 17.1 Cinnamon in which I am permanently stuck in fallback mode (that is, unless I hard shutdown or reboot) on an aging laptop with AMD Radeon HD 4200 graphics (considered legacy). I believe this issue was caused by a failed install of AMD's latest linux graphics drivers, in which I literally opened the .run file and attempted to install. The install failed (some error), of course, but when I rebooted, I was kicked into fallback. After some googling, I autoremoved fglrx then installed fglrx, as I read would reinstall fglrx, the proprietary drivers for AMD cards and rebooted. Still stuck in fallback. I removed and installed Xorg and rebooted. Still stuck in fallback. I downloaded the AMD legacy drivers from AMD's site (my card's series included with this set). Had to change the permissions to run this .run file but eventually ran it from terminal, but this install also failed (claimed I was missing tool(s), despite not indicating precisely what I was missing). I'm still rummaging around for fixes, but maybe asking can help. I can provide some more info below, but let me know what else you need (and how to get it) if you wish to help. I really want linux to work out for me instead of shelling out $$ for Windows, but so far this has been a rocky start. Thanks


Code:

inxi -G

yields
Code:

Graphics:   Card: AMD RS880M [Mobility Radeon HD 4225/4250]
X.Org: 1.15.1
drivers: fbdev,ati,radeon (unloaded: fglrx,vesa)
Resolution: 1024x768@76hz
GLX Renderer: N/A
GLX Version: N/A

Code:

lshw -C video

yields
Code:

*-display UNCLAIMED
description: VGA compatible controller
product: RS880M [Mobility Radeon HD 4225/4250]
vendor: AMD
physical id: 5
...(bunch of stuff on specs)

Have also did apt-get update and apt-get dist-upgrade.
Still no luck, let me know what you think.

hello, i have installed ubuntu one hour ago and i cant change my screen resolution. In displey options i have only two basic options: 1024x768 and 800x600. My monitor is has a resolution of a 1920x1080 and on windows it works fine. I havent checked third-party softwares when i was installing ubuntu and i think that i past by graphic driver(on windows i had ati control center). If anyone can help im using Gigabyte radeon r7 260x oc 1gb ddr5. I would realy love to change my screen resolution and play games.

Hello, my video card "Advanced Micro Devices [AMD] nee ATI Cedar PRO [Radeon HD 5450/6350]"
create something which can be seen with dmesg "drm: registered panic notifier".
Should I install the fglrx driver instead of keeping the open source radeon as per current install?
I have antix which is a debian wheezy based system https://wiki.debian.org/ATIProprietary# ... 2Wheezy.22
Thanks for any advice before I do it.

Hey guys. So I just went out and bought a Sager 8268-s (clevo p150sm-a) With an i7 4910mq and a Nvidia 980m gt. As I am a computer tech by trade, every time i see Windows i get horrible PTSD so i decided to try Linux instead. After many hours of trying to get a dual boot working finally got Linux Mint 17 Cinnamon installed on my computer, but when I went to install the Nvidia driver it landed me in fallback mode which I could not escape. So then I tried Ubuntu 14.04 LTS thinking maybe Mint was incompatible with the driver and the same thing happened.

So here is my method:

(sorry i don't know how to make a code box :/ )

First I log in to get root access:

$ su

Then I Update the xorg:

$ sudo apt-add-repository ppa:xorg-edgers/ppa

Then update my system:

$ sudo apt-get update && sudo apt-get dist-upgrade

Then i go into Virtual terminal (Ctrl+Alt+F1) and disable the display manager:

$ sudo service mdm (or lightdm for Ubuntu) stop

Then i install the drivers which i have done multiple ways:

$ sudo apt-get install nvidia-current nvidia-settings

or

$ sudo apt-get install nvidia-343 nvidia-settings

or by downloading the driver from Nvidia (first designating the file as executable)

$ sudo sh nvidia.run && sudo apt-get install nvidia-settings

Then after install, I create the config file:

$ sudo nvidia-xconfig

Then I reboot. After I get the low res mode in Ubuntu or fallback mode in Mint and Driver manager doesn't detect any proprietary drivers and I have to reinstall to get the OS working again. Any suggestions would be greatly appreciated.

Just did an update via terminal:

Calculating upgrade... Done
The following packages were automatically installed and are no longer required:
linux-headers-3.13.0-49 linux-headers-3.13.0-49-generic
linux-image-3.13.0-49-generic linux-image-extra-3.13.0-49-generic
Use 'apt-get autoremove' to remove them.
The following NEW packages will be installed:
fglrx-core linux-headers-3.13.0-53 linux-headers-3.13.0-53-generic
linux-image-3.13.0-53-generic linux-image-extra-3.13.0-53-generic
The following packages will be upgraded:
accountsservice apport apport-gtk fglrx fglrx-amdcccle fuse
libaccountsservice0 libfuse2 liboxideqt-qmlplugin liboxideqtcore0
liboxideqtquick0 libspice-server1 linux-firmware linux-headers-generic
linux-image-generic linux-libc-dev oxideqt-codecs-extra python3-apport
python3-problem-report
19 upgraded, 5 newly installed, 0 to remove and 0 not upgraded.
Need to get 227 MB of archives.
After this operation, 490 MB of additional disk space will be used.
Do you want to continue? [Y/n] Y

It downloaded and unpacked files, everything was automated until it asked for my input before replacing the following files:
I backed them up then chose to replace them:

DKMS: install completed.
update-initramfs: deferring update (trigger activated)
Setting up fglrx (2:15.200-0ubuntu0.3) ...

Configuration file '/etc/ati/amdpcsdb.default'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** amdpcsdb.default (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/amdpcsdb.default ...

Configuration file '/etc/ati/atiapfxx'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** atiapfxx (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/atiapfxx ...

Configuration file '/etc/ati/control'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** control (Y/I/N/O/D/Z) [default=N] ? ^[Y

Configuration file '/etc/ati/control'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** control (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/control ...

Configuration file '/etc/ati/signature'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** signature (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/signature ...

Configuration file '/etc/ati/atiapfxx.log'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** atiapfxx.log (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/atiapfxx.log ...

Configuration file '/etc/ati/atiapfxx.blb'
==> File on system created by you or by a script.
==> File also in package provided by package maintainer.
What would you like to do about it ? Your options a
Y or I : install the package maintainer's version
N or O : keep your currently-installed version
D : show the differences between the versions
Z : start a shell to examine the situation
The default action is to keep your current version.
*** atiapfxx.blb (Y/I/N/O/D/Z) [default=N] ? Y
Installing new version of config file /etc/ati/atiapfxx.blb ...
Creating backups for the fglrx-core transition
update-alternatives: warning: forcing reinstallation of alternative /usr/lib/fglrx/ld.so.conf because link group x86_64-linux-gnu_gl_conf is broken
Restoring backups for the fglrx-core transition
Setting up fglrx-amdcccle (2:15.200-0ubuntu0.3) ...
Setting up linux-firmware (1.127.12) ...
Setting up linux-headers-3.13.0-53 (3.13.0-53.89) ...
Setting up linux-headers-3.13.0-53-generic (3.13.0-53.89) ...
Examining /etc/kernel/header_postinst.d.
run-parts: executing /etc/kernel/header_postinst.d/dkms 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic

Good news! Module version for fglrx.ko
exactly matches what is already found in kernel 3.13.0-53-generic.
DKMS will not replace this module.
You may override by specifying --force.
Setting up linux-headers-generic (3.13.0.53.60) ...
Setting up linux-image-extra-3.13.0-53-generic (3.13.0-53.89) ...
run-parts: executing /etc/kernel/postinst.d/apt-auto-removal 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
run-parts: executing /etc/kernel/postinst.d/dkms 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
update-initramfs: Generating /boot/initrd.img-3.13.0-53-generic
run-parts: executing /etc/kernel/postinst.d/pm-utils 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
run-parts: executing /etc/kernel/postinst.d/update-notifier 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.13.0-53-generic /boot/vmlinuz-3.13.0-53-generic
Generating grub configuration file ...
Found theme: /boot/grub/themes/Zorin/theme.txt
Found linux image: /boot/vmlinuz-3.13.0-53-generic
Found initrd image: /boot/initrd.img-3.13.0-53-generic
Found linux image: /boot/vmlinuz-3.13.0-52-generic
Found initrd image: /boot/initrd.img-3.13.0-52-generic
Found linux image: /boot/vmlinuz-3.13.0-51-generic
Found initrd image: /boot/initrd.img-3.13.0-51-generic
Found linux image: /boot/vmlinuz-3.13.0-49-generic
Found initrd image: /boot/initrd.img-3.13.0-49-generic
Found linux image: /boot/vmlinuz-3.13.0-48-generic
Found initrd image: /boot/initrd.img-3.13.0-48-generic
Found linux image: /boot/vmlinuz-3.13.0-46-generic
Found initrd image: /boot/initrd.img-3.13.0-46-generic
Found memtest86+ image: /boot/memtest86+.elf
Found memtest86+ image: /boot/memtest86+.bin
No volume groups found
Found Windows XP Professional x64 Edition on /dev/sda1
done
Setting up linux-image-generic (3.13.0.53.60) ...
Setting up oxideqt-codecs-extra:amd64 (1.7.8-0ubuntu0.14.04.1) ...
Setting up liboxideqtcore0:amd64 (1.7.8-0ubuntu0.14.04.1) ...
Setting up liboxideqtquick0:amd64 (1.7.8-0ubuntu0.14.04.1) ...
Setting up liboxideqt-qmlplugin:amd64 (1.7.8-0ubuntu0.14.04.1) ...
Processing triggers for libc-bin (2.19-0ubuntu6.6) ...
Processing triggers for initramfs-tools (0.103ubuntu4.2) ...
update-initramfs: Generating /boot/initrd.img-3.13.0-53-generic
W: Operation was interrupted before it could finish

Finally the error in red immediately above pops up.
I searched the net and found a site with an article dated back in 2010 that said to fix the error before rebooting or I'd probably not be able to boot to Linux.
Which I'm doing right now, I've not yet rebooted.

How should I recover from such an error before I reboot.

The site had several solutions depending upon other variables, one of which was to delete and/or re-run something. But none of the solutions seemed to fit my case.

I'm running the Zorin OS 9 Theme on top of Ubuntu 14.04 LTS, an AMD PhenomII 64bit 4 core processor on an ASUS MB. The video card is also an AMD/ATI, hence the need for the fglrx drivers listed above.

I'm not sure if the overwriting of the ATI/AMD driver config files shown above are responsible for the error or not. I did nothing that I was aware of that might have caused it, except close another instance of terminal that was runnning, and a libre office writer window.

Any ideas on how to solve this before I reboot would be greatly appreciated.

TIA

Hello everyone.
I have just installed debian stable non-free onto my hard drive but the sound isn't working.

I've been to the debian site https://wiki.debian.org/SoundConfiguration and found that 'users' don't automatically have access to audio (for security reasons).
So I did the following command as root (sudo):
Code:

adduser USER_NAME audio

Now when I am 'user', I can get sound.

I also did:
Code:

chgrp cdrom /dev/sr0
adduser USER_ID cdrom

This allows 'user' to get sound from the cdrom.

I then went onto the debian soundfaq https://wiki.debian.org/SoundFAQ

From the 'lspci -v' command, I get these 2 outputs which have the word 'audio' in it:
Code:

01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS880 HDMI Audio [Radeon HD 4200 Series]
	Subsystem: Giga-byte Technology Device 960f
	Flags: bus master, fast devsel, latency 0, IRQ 19
	Memory at fdefc000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: snd_hda_intel

00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
	Subsystem: Giga-byte Technology Device a102
	Flags: bus master, slow devsel, latency 32, IRQ 16
	Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: snd_hda_intel

So I have 2 sound cards.

The debian website says: 'If sound does not work for root account as well, then that means that either your sound card is not supported by Debian or it was not configured properly'.

Ok, so the first part of the statement is worrying.
So I went to the debian device driver check page http://kmuto.jp/debian/hcl/ and did 'lspci -n'.
The output can be pasted onto their web page and debian will say if the sound cards are supported.
The web page shows that the sound cards are supported:

Quote:
10024383 Yes Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) snd-hda-intel v2.6.25
10029715 Yes Advanced Micro Devices [AMD] nee ATI RS880 [Radeon HD 4250] radeon v2.6.35-
1002970f Yes Advanced Micro Devices [AMD] nee ATI RS880 HDMI Audio [Radeon HD 4200 Series] snd-hda-intel v2.6.27-
So now I'm guessing that my sound cards are 'not configured properly'. But I've run a Youtube video and then changed the sound cards under alsamixer and I still don't get sound.
Is there is a simple solution to this please? Thank you in advance.

Hi,
These NVIDIA products are real nightmares. I recently downloaded a copy a sabayon linux for my desktop.
The live dvd booted with the following error message throughout the screen

Quote:
[ 3129.434776] NVRM: No NVIDIA graphics adapter found!
[ 3129.434855] NVRM: NVIDIA init module failed!
[ 3129.479276] NVRM: The NVIDIA GeForce 7025 / nForce 630a GPU installed in this system is
NVRM: supported through the NVIDIA 304.xx Legacy drivers. Please
NVRM: visit http://www.nvidia.com/object/unix.html for more
NVRM: information. The 340.58 NVIDIA driver will ignore
NVRM: this GPU. Continuing probe...
[ 3129.479285] NVRM: No NVIDIA graphics adapter found!
[ 3129.479362] NVRM: NVIDIA init module failed!
[ 3129.519879] NVRM: The NVIDIA GeForce 7025 / nForce 630a GPU installed in this system is
NVRM: supported through the NVIDIA 304.xx Legacy drivers. Please
NVRM: visit http://www.nvidia.com/object/unix.html for more
NVRM: information. The 340.58 NVIDIA driver will ignore
NVRM: this GPU. Continuing probe...
However after a long time it started up properly. After installing the os I found that the problem still persists. Firtsly it took about 10 mins or so to boot. And then apart from terminal 7 (which is the graphical terminal) all other terminals shows the above output. It seems like it has fallen through an infinite loop. I tried downloading some drivers from the nvidia site but simply could not install them because it mandates the X to stop working. If I do so I won't be able to install it from other terminals.

I have attached the output of "dmesg".
Any help is appreciated.

I install fgrlx driver on vivid os the driver look like is istalled correct on system and built the necessary kernel modules because the dpkg log not report any errors, i configured the driver by simple commands like:

sudo aticonfig --initial

sudo aticonfig --screen-layout=on

i reboot the machine , but i face an strange issue the boot splash screen is hangup,i cant enter my lvm password to boot the system, i was have a chance to boot into rescue mode when boot to rescue mode the display not read by the system i try to export display by

export DISPLAY=:0

I try to configure /etc/X11/xorg.conf there is not good resaults the boot splash still hang up

I edited the grub , i uncomment "quiet splash" modified by "nomodeset"

i can boot without boot splash but im faced other issue i cant switch to virtual tty

i dont know is this a bug in the driver or in the kernel

any suggest

OK,

Lastnight I decided to finally attempt to install the dedicated ATI/AMD Catylist drivers. After all I was successfull with the HP drivers, right...

No matter which grub selection I make, getting in is broken, except of course for the Windows XP Pro x64 entry, that works just fine. I'm here with you today, because of the Fedora 21 Live DVD, (slooooww).

Here is the drivers log file:

==========================================================
Supported adapter detected.
Check if system has the tools required for installation.
Uninstalling any previously installed drivers.
Unloading radeon module...
rmmod: ERROR: Module radeon is in use
Unloading drm module...
rmmod: ERROR: Module drm is in use by: ttm drm_kms_helper radeon
[Message] Kernel Module : Trying to install a precompiled kernel module.
[Message] Kernel Module : Precompiled kernel module version mismatched.
[Message] Kernel Module : Found kernel module build environment, generating kernel module now.
AMD kernel module generator version 2.1
doing Makefile based build for kernel 2.6.x and higher
rm -rf *.c *.h *.o *.ko *.a .??* *.symvers
make -C /lib/modules/3.18.3-201.fc21.x86_64/build SUBDIRS=/usr/lib/modules/fglrx/build_mod/2.6.x modules
make[1]: Entering directory '/usr/src/kernels/3.18.3-201.fc21.x86_64'
CC [M] /usr/lib/modules/fglrx/build_mod/2.6.x/firegl_public.o
/usr/lib/modules/fglrx/build_mod/2.6.x/firegl_public.c:6396:12: warning: ‘KCL_fpu_save_init’ defined but not used [-Wunused-function]
static int KCL_fpu_save_init(struct task_struct *tsk)
^
CC [M] /usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o
/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.c: In function ‘KCL_ACPI_Slot_No_Hotplug’:
/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.c:845:21: error: ‘struct acpi_device_flags’ has no member named ‘no_hotplug’
tdev->flags.no_hotplug = true;
^
scripts/Makefile.build:257: recipe for target '/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o' failed
make[2]: *** [/usr/lib/modules/fglrx/build_mod/2.6.x/kcl_acpi.o] Error 1
Makefile:1385: recipe for target '_module_/usr/lib/modules/fglrx/build_mod/2.6.x' failed
make[1]: *** [_module_/usr/lib/modules/fglrx/build_mod/2.6.x] Error 2
make[1]: Leaving directory '/usr/src/kernels/3.18.3-201.fc21.x86_64'
Makefile:88: recipe for target 'kmod_build' failed
make: *** [kmod_build] Error 2
build failed with return value 2
[Error] Kernel Module : Failed to compile kernel module - please consult readme.
[Reboot] Kernel Module : dracut
==========================================================

I just rebooted without attempting to configure the card, as per the ATI/AMD warning stating that it's important to do so, because my thinking was derailed due to seeing errors, and the install program said I needed to reboot. Afterall, I just couln't believe that with a "Failed to compile kernel module" error, it would actually keep the changes I'd made, that surely Linux had a failsafe in place for such circumstances. In other words, I'm also a newbie, and just don't know how many hoops of fire one has to jump through to be at peace with linux.

Can anyone please help be get back into my install, I've already set up so many things, there's just got to be a way, right?


Thanks in Advance!


JustAnotherHuman