New Install Boot

Machine is booted into Grub Menu
I am using rescue linux

by doing fdisk -l

it shows
Disk /dev/sda : bla bla bla
Device Boot
/dev/sda1 *

so i install grub using this command in shell

grub-install /dev/sda1

it shows

installation finished. No error reported
This content of the device map /boot/grub/device.map


After re-boot it again shows grub menu

Hi guys,

I'm new to this forum and linux too.
I thought of installing a lightweight distro of linux and did some research on the net where I found people recommending Puppy Linux. Plus it is (theoretically speaking) possible to run it from a USB (flash) drive which I decided to try out but it seems like it's not that simple a task as a lot of people (all over the internet) say it is.

What I tried so far is this: installing it into a thumb drive using unetbootin follwing a youtube tutorial (which basically showed how to download an iso of puppy, use unetbootin to make the thumbdrive bootable and install puppy on it). It didn't work. The USB wasn't recognized as a bootable device. I know for sure it can be booted from it since I tried ubuntu from the same USB and the same Laptop (which is able to boot from USB).

I thought that something with the Flash Drive not OK so I tried to use a windows installer to install puppy like other windows programms but this didn't work either. This time Puppy was recognized because there was an option to boot either Puppy or Windows 7 but when I chose to boot from Puppy nothing happens just a screen flash, some letters in the top left corner saying something like NTSC or NTSF (I can't read it properly because it goes away too fast) then after the screen flash the whole thing again (boot from win 7 or Puppy I choose Puppy again the flash... basically a loop).

Any ideas what I'm doing wron or what the problem is?

Thank You for any replies.

Hi All,

I recently decided to tryout Linux and dual booted my laptop (originally just had windows 8) with Xubuntu. Now I want to try out Kali Linux. So I downloaded Kali and made a bootable USB, the problem is that when I try to boot from the USB it just brings up the grub menu asking me to select Xubuntu, Windows etc. I've changed the boot menu in the BIOS but that has no effect.

I've tried booting into windows and the restarting by holding shift but when I select the usb option it just says:

"system doesn't have any USB boot option. Please select other boot option in Boot Manager Menu"

and then returns to the grub menu. I don't understand because I used a bootable usb to install xubunto?

I'd be really grateful if anyone can help me out with this!

Thanks

I have a dual boot laptop with debian stable & Windows 7.

The HD partitions a
sda1: NTFS for W7
sda2: FAT32 (currently unused)
sda3: linux /boot
sda4: linux ext4, which is LVM with encryption

I've re-installed W7 and now need to recover the MBR & grub menu.

I've booted with the netinst usb in rescue mode, but it fails to mount the root partition /sda4:
"An error occured while mounting the device you entered for your root file system (/dev/sda4) on /target"

and /var/syslog shows:
Code:

rescue-mode: selected root device '/dev/sda4'
umount: cant umount /target: Invalid argument
isofs_fill_super: bread failed, dev=sda4, iso_blknum=16, block=32
EXT2-fs (sda4): error: unable to readsuperblock
EXT3-fs (sda4): error: unable to readsuperblock
rescue: mount: mounting /dev/sda4 on /target failed: Invalid argument

So it seems like something is wrong with the mount command?

Would appreciate suggestions how to solve this.

Thanks

Hi,

I installed ghostscript via yum package manager. Later I wanted a newer version of ghostscript and compiled it from source. "make install" placed the gs executable file under /usr/local/bin/gs. This works if I run the command with absolute path, but if try to run gs, the shell will output

"-bash: /usr/bin/gs: No such file or directory"

if I echo the path variable it will display

/usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin

If i run whereis it will give me the correct path
gs: /usr/local/bin/gs

How do I make it work so that typing "gs" will run the executable file from the /usr/local/bin/gs?

(I am using Centos 6)

Thanks.

Hello,

I am performing work on a particularly large set of files (around 5GB in total). I get the message: error writing temporary file: No space left on device when trying to run my script and presume it's because of the 2GB limit on my tmp folder.

How do either:

a) increase the size of my tmp folder
b) tell my process to use another folder instead of tmp?

Hi,

I am new to the installation of Linux, and wish to install 3 different distro's on the same hard disk.

I have installed Centos 7 successfully as follows :

The /boot is /dev/sda2

/dev/sda1 is listed as unknown so i assume it is the Master Boot Record with Grub installed. I do obtain the option to boot to the various kernels after updating the OS.

/dev/sda3 is a Linux LVM with the various partitions i required.

When i installed the CentOS 7 the installer stated an error about the bootable partition - which was effectively /boot, so i moved this to /dev/sda2.

What i am not sure about is that if i want to install 2 other Linux OS's will i run out of /dev/sdaX assignments ?.

I read somewhere that there are 4 maximum that can be used a /boot (SDA1, SDA2, SDA3, SDA4), so does this mean i can only install one other OS ?.

Any guidance gratefully received. Thanks.

Regards,

Richard.

how to fix boot menu so it can be read?

Arch linux, lxdm/lxde, recent installation, feeling I must be doing something stupid, would be glad to be guided!

I have a Brother HL-2030 printer connected to a Raspberry Pi as a print server, CUPS setup, with sharing turned on. Other machines in the household, and indeed other OS's on the machine I'm writing on, print trouble-free to this printer.

On *this* desktop machine, (with libcups installed,) other programs print trouble-free. Firefox, Thunderbird, geany and evince all detect the presence of the network printer, and work as expected.

It's just Libreoffice that does not. This is true both of libreoffice-fresh and libreoffice-still, and it is true for all the components (write, draw, calc etc).

Libreoffice *does* find the network printer from other OS's that I play with; I have Puppy and Mint on the same machine, but those installs of Libreoffice are obviously different/earlier versions (nor do I feel like upgrading them in the circumstances!)

In this context, though, the Libreoffice "File>Printer settings..." menu offers me only a "Generic Printer" (whose properties and options I can edit). If I ask Libreoffice to print to this generic printer, it reports no failure, but that task just seems to disappear into thin air.

On the Pi server, /var/log/cups/ offers

Code:

# extract from /var/log/cups/access_log
# [...snip]
192.168.2.2 - - [22/Jan/2015:18:21:21 +0000] "POST / HTTP/1.1" 200 566 CUPS-Get-Printers server-error-version-not-supported
192.168.2.2 - - [22/Jan/2015:18:21:21 +0000] "POST /printers/Brother_HL-2030_series HTTP/1.1" 200 15824 Print-Job successful-ok
# the above line logs a successful print from geany
192.168.2.2 - - [22/Jan/2015:18:26:40 +0000] "POST / HTTP/1.1" 200 673 CUPS-Get-Default server-error-version-not-supported


# extract of /var/log/cups/error_log
# [...snip]
E [22/Jan/2015:18:21:20 +0000] Returning IPP server-error-version-not-supported for CUPS-Get-Printers (no URI) from 192.168.2.2
E [22/Jan/2015:18:21:20 +0000] Returning IPP server-error-version-not-supported for CUPS-Get-Printers (no URI) from 192.168.2.2
E [22/Jan/2015:18:21:21 +0000] Returning IPP server-error-version-not-supported for CUPS-Get-Printers (no URI) from 192.168.2.2
E [22/Jan/2015:18:26:40 +0000] Returning IPP server-error-version-not-supported for CUPS-Get-Default (no URI) from 192.168.2.2

I really think I must be doing something very stupid and newbie-ish!

I'm trying to get MRTG set up on Ubuntu 14.04 and cannot get snmpd to install correctly. Every time I try to install I get this error

/usr/sbin/snmpd: error while loading shared libraries: libnetsnmpagent.so.30: cannot open shared object file: No such file or directory
invoke-rc.d: initscript snmpd, action "start" failed.
dpkg: error processing package snmpd (--configure):
subprocess installed post-installation script returned error exit status 127
Processing triggers for ureadahead (0.100.0-16) ...
Errors were encountered while processing:
snmpd
E: Sub-process /usr/bin/dpkg returned an error code (1)

I've tried numerous possible fixes for this and have not found anything that works. Any help is greatly appreciated.