Need Help In Loading Snort

Hello everyone. I am attempting to get Snort to recognize a Portscan and have an alert pop up on the screen. I have successfully installed and run snort in multiple types of configurations. I have enabled the sfportscan preprocessor in my snort.conf Snort is running on Ubuntu and I am running nmap on a Kali box. Can anyone offer any insight on how to configure snort to have an alert pop up when it detects any type of portscan?

Thanks,
-Trevor

I was copying the contents of a flash drive to a folder. In the middle of it I got an error message:

'Error splicing file: input/output error'

and then it said 'do you want to skip or retry?' And the "all" button was there too. Anyway, I skipped. When I checked the folder, all my data seemed to be there.

Do you think it was?

I mean, what are the implications of the error message and of my "skipping" it?

Next up, when I looked at the contents of my flash drive all the folders and files have a lock icon on them. I can open the files but I can't edit them. And no, the lock switch on my flash drive is not pressed.

Any ideas?

Thanks.

Dear all;
I run an execute file named "A" gets it's input from a text file "B.inp"
but I face this error:
A < B.inp
: error while loading shared libraries: libquadmath.so.0: cannot open shared object file: No such file or directory

I've downloaded libquadmath and when I want to install it ,the other error said I don't have libgc package!!! but I have libgc!! is it because of existing two different repository that it can't share their information?
my operating system is Centos6;
what shall I do?
Thanks for your attention

Hello,
I have installed LEACH in NS-2.34 (ubunto-14.04)

I could run it successfully..

But it always stopped in a few seconds without sending data

i.e. Total Data=0

And it consumed a large energy!!!!

It didn't show any error in leach.error

Is it a logical error or others?

thanks

When I try to open my filesystem I get the following error message:

Unable to mount 496GB filesystem error mounting:mount:wrong fs type, bad option,bad superblock on /dev/sdb2, missing codepage or helper program, or other error. In some cases useful info is found in syslog - try dmesg | tail or so. What does all this mean? Everything had worked so far until now. I'm using Debian V 7.8.0

Thanks for any help I can get

Gary

Greetings All,

I'm NEW to Linux 13.10. I'm getting a error message on start up.
In the past, I would just press S to skip mounting. That is NOT
working any more.

Error Message : An error occurred while mounting/mnt/3F3C-1AF6.
Press S to skip mounting or M for manual recovery

Is there a command, that I can use to continue to boot or at
least find out what is wrong with my Ubuntu 13.10?
When I press S or M .... nothing happens.

Thanks in advance!

PEACE to ALL .... MJ

Please forgive me but I'm a little new to Red Hat (RHEL 5). I'm using rysnc to backup critical data and to a second disk; here is what I'm typing at the command line rsync -rvgal /data/disk1/share /data/backup/share. It appears that the softlinks are not transfered to the backup drive and some of the links point to data not located in the source folder (/data/share). After reading the rsync man page I was a little confused about the L option (vs the l option). In order to ensure that the linked files are moved should I type the below:

rsync -rvgaL /data/disk1/share /data/backup/share

A million thanks,
Johnny Mac

Hi all,

now i need to know

i) how to add encryption and decryption in any of routing-(DSDV,DSR,AODV,OLSR)?

ii) As of now in routing i am able to see only data flows, but is it possible to send some data(message) from source node and i want to retrieve(read) those messages from receiver nodes?

Since i am beginner, Quote:
i dont know whether my question is right or wrong?
Thanks

Pon

I`ve got this error message:
Sun May 31 01:03:53 2015
Disk cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
Disk exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 fro
Disk status: { DRDY ERR }, Disk configured for UDMA/33
Disk qc timeout (cmd 0xa0)
sr 0:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
ata1: EH complete
ata1: link is slow to respond, please be patient (ready=0)
ata1: soft resetting link
res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout)
ata1: device not ready (errno=-16), forcing hardreset

Could you help me with the solution?
Thanks a lot.

i'm new to linux and ns2 platform, i'm doing my thesis and trying to run AODV code, i got the following error, anyone can sort me out

thanks in advance

$ ns DSR.tcl
num_nodes is set 50
warning: Please use -channel as shown in tcl/ex/wireless-mitf.tcl
INITIALIZE THE LIST xListHead
Loading connection pattern...
Loading scenario file...
Starting Simulation...
SORTING LISTS ...DONE!
channel.cc:sendUp - Calc highestAntennaZ_ and distCST_
highestAntennaZ_ = 1.5, distCST_ = 550.0
Segmentation fault (core dumped)