Please Help !

Hi

My wifi isn't working. Broadcom 14e4:43a0 is what I got. Running off a USB on Macbook. Cant apt-get update or install anything as there is no wifi. There is no ethernet port either. I might need the drivers i think ? Maybe its a quick fix ! Please help !!

Thanks in advance.

Hi ,

I'm new to Linux , I installed Kali linux on my pc and the wifi card isn't working ..

It is a usb wifi card , It has a cd for its driver. There is a folder in the cd called " Linux Driver " and here's what is inside it

First folder :

http://imgur.com/WTNgnEm

Second folder :

http://imgur.com/PyH07Cs

And here it is when I write lsusb :

http://i.imgur.com/NiPbbxSh.jpg

I'd like to know the steps to install it , Thanks in advance ..

Hi everyone, I am a new member and also new to linux, I encountered a problem, but last week I tried but did not solve
I downloaded iso file linux 1.1.0 on page potassium https://www.kali.org, I installed on my Dell inspiron n4010, it works very well and does not have any errors, but after I update and upgrade all packages, I rebooted the system switches to the command line, I lost a lot of time to return to the graphics, but when booting up the network manager icon not seen, I have set the package network-manager-gnome_0.9.4.1-0ubuntu2_i386.deb network manager icon show but when click on the network manager icon only contained text "network manager is not running."
I also installed Wicd but could not run "could not connect to wicd's D-Bus interface. Check the wicd log for error messages."
wireless driver apparently was set before
root@kali:~# airmon-ng
PHY Interface Driver Chipset

phy0 wlan0 wl Broadcom Corporation BCM4313 802.11b/g/n (rev 01)

please help me!
please guide installed offline, my kali linux no internet connection. can download package from another machine to install.

hi there once again
Now I am getting this problem which running the cmd "honeyd -d -f honeyd.conf"
root@kali:/etc/honeypot# honeyd -d -f honeyd.conf
Honeyd V1.5c Copyright (c) 2002-2007 Niels Provos
honeyd[4726]: started with -d -f honeyd.conf
honeyd[4726]: listening promiscuously on eth0: (arp or ip proto 47 or (udp and src port 67 and dst port 68) or (ip )) and not ether src 98:4b:e1:94:62:46
honeyd[4726]: [eth0] trying DHCP
honeyd[4726]: Demoting process privileges to uid 65534, gid 65534
honeyd[4726]: [eth0] got DHCP offer: 192.168.23.2
honeyd[4726]: Updating ARP binding: 00:00:24:26:26:1d -> 192.168.23.2
honeyd[4726]: arp reply 192.168.23.2 is-at 00:00:24:26:26:1d
honeyd[4726]: TTL exceeded for dst 224.0.0.22 at gw 10.0.0.1
honeyd[4726]: No reverse routing map for 10.0.0.1
honeyd[4726]: TTL exceeded for dst 224.0.0.22 at gw 10.0.0.1
honeyd[4726]: No reverse routing map for 10.0.0.1
honeyd[4726]: TTL exceeded for dst 224.0.0.22 at gw 10.0.0.1
honeyd[4726]: No reverse routing map for 10.0.0.1
honeyd[4726]: TTL exceeded for dst 224.0.0.22 at gw 10.0.0.1
honeyd[4726]: No reverse routing map for 10.0.0.1

what does it mean? because it starts to spam the terminal with such errors. or it is not??

I think, I have to edit the "honeyd.conf" file, but no clue.
the following is my honeyd configuration.

route entry 10.0.0.1
route 10.0.0.1 link 10.2.0.0/24
route 10.0.0.1 add net 10.3.0.0/16 10.3.0.1 latency 8ms bandwidth 10Mbps
route 10.3.0.1 link 10.3.0.0/24
route 10.3.0.1 add net 10.3.1.0/24 10.3.1.1 latency 7ms loss 0.5
route 10.3.1.1 link 10.3.1.0/24

# Example of a simple host template and its binding
create template
set template personality "Microsoft Windows XP Professional SP1"
set template uptime 1728650
set template maxfds 35
# For a complex IIS server
add template tcp port 80 "sh /usr/share/honeyd/scripts/win32/web.sh"
add template tcp port 22 "/usr/share/honeyd/scripts/test.sh $ipsrc $dport"
add template tcp port 23 proxy $ipsrc:23
add template udp port 53 proxy 141.211.92.141:53
set template default tcp action reset
# Use this if you are not running honeyd as 'honeyd' user:
# Debian-specific (use nobody = 65534 instead of 32767)
# set template uid 65534 gid 65534

create default
set default default tcp action block
set default default udp action block
set default default icmp action block

create windows
set windows personality "Microsoft Windows XP Professional SP1"
set windows default tcp action reset
add windows tcp port 135 open
add windows tcp port 139 open
add windows tcp port 445 open

set windows ethernet "00:00:24:ab:8c:12"
dhcp windows on eth0


urgent help needed please. thanks in advance

I have been flailing trying to get a web server running on Fedora 21.

Finally did so.

I have my iptables working (me thinks) as they should. I can connect from my Linux box (local) or from my Mac on the same network/subnet.

Problem is in my "travels" I have somehow trashed my firewall-cmd.

I was adding parameters to it w/o issue. E.G
firewall-cmd --zone=public --add-port=80/tcp --permanent
Then restarting firewall-cmd
firewall-cmd --realod

This was all working. I "fixed" my problem with connecting to my web server from other LAN workstations (iptables issues) and was going back to see if all was well. Now when I try to restart I get a:
FirewallD is not running
That from my "reload" command above.

Have I fixed my web server issue or is my world wide open att?

Assistance, as always, greatly appreciated.

Skip

Im not sure if anyone has already asked this question but i would really like to know how to disable Sleep/Hibernate completely and persistently on a Kali Linux 1.1.0 System running dual boot on a Macbook Pro Mid 2009.

Hello there,
i've just installed the ubuntu 1.4 version in my laptop alongside a version of windows 7. The problem is that while working with ubuntu i cannot operate the wifi connection to my modem, looks like the driver is not working, any ideas?
thank you in advance

I recently decided to upgrade from Debian Squeeze to Wheezy. Update seemed to go fine with the exception of the following warning concerning my Broadcom bmc5704 gigabit ethernet cards

Quote:
W: Possible missing firmware /lib/firmware/tigon/tg3_tso5.bin for module tg3
W: Possible missing firmware /lib/firmware/tigon/tg3_tso.bin for module tg3
W: Possible missing firmware /lib/firmware/tigon/tg3.bin for module tg3
No problem I will simply install the missing .bin files after the upgrade. Get the .bin files from the Debian repository and install them using the command "dpkg -i file_name.deb" then ran "apt-get install -f" for good measure. Still nothing, I have downloaded the following files and running that same command for each hoping that this would solve my compatibility issue with no such luck.

Quote:
firmware-bnx2_0.36+wheezy.1_all.deb
firmware-bnx2x_0.36+wheezy.1_all.deb
firmware-linux-nonfree_0.36+wheezy.1_all.deb
firmware-linux-nonfree_0.36+wheezy.1~bpo60+1_all.deb
When I attempt to go into System Preferences > Network I get the message "The system network services are not compatible with this version."

I showed the hardware using the lshw command and here is the entry concerning the ethernet interface

Quote:
#output from lshw command

*-network:0
description: Ethernet interface
product: NetXtreme BCM5704 Gigabit Ethernet
vendor: Broadcom Corporation
physical id: 2
bus info: pci@0000:02:02.0
logical name: eth0
version: 10
serial: 00:13:21:b2:cf:46
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 66MHz
capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.116 duplex=full firmware=5704-v3.41, ASFIPMIc v2.36 ip=XX.XX.XX.154 latency=64 link=no mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:25 memory:fdf70000-fdf7ffff
Network file configuration.

Quote:
# Network file

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address XX.XX.XX.XX
netmask 255.255.255.0
network XX.XX.XX.0
broadcast XX.XX.XX.255
gateway XX.XX.XX.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers XX.XX.XX.XX 8.8.8.8
dns-search XXXXXXX.net
Server is an older HP ProLiant and I am attempting to put Wheezy on it from a direct upgrade from squeeze.

At this point I am stumped. Not sure exactly what to do but it seems like a fairly simple fix. If anyone has any suggestions I would sure appreciate the help. Let me know if you need anything.

So I was able to successfully install CyberDuck on my MacBook and configure it with my VPS using SSH Authentication Keys and a Passphrase on my Private Key.

It seems to be working well, and I feel like I can trust it when uploading files to my VPS.

But what about downloading?

This may sound dumb, but I am not entirely sure how to securely download things (e.g. Server Backups) from my VPS to my MacBook using CyberDuck...

Sincerely,


Rob

Again my friends I am having trouble,
Have Toshiba Tecra 64-bit 500gb disk 4gb ram running Windows 7 professional it has Intel core i5 processor.
I burned iso file of DVD LinuxMint Rebecca Cinnamon to DVD.
When I restart the system with the DVD inserted it immediately opens in Windows 7.
Then I pressed F1 to change the boot order to USB ODD.
Then I re-started several times to no avail.
When I press F1 to select the boot device it only gives me the Windows 7 option.
I know the disk is good because I checked the files it should contain and they are there.
Help from anyone is greatly appreciated.
Best regards to all of you.